Njd clone analog dub siren
Hello,im start in project electronic.i have the squematic but i dont know translater to fritzing.could somebody help me please¿
View ArticleQuestion about jumpers
Don't know about the jumper question, although as a work around a one pin connector on each end of the jumper will do. That creates a pad that you can solder a wire to. I'd say post your board at...
View ArticleNjd clone analog dub siren
If you have a schematic, then you should start fritzing, then select the components in the schematic (you may have to search for / create some components if they aren't in fritzing) and then drag them...
View ArticleClik here to view.
2mm header PCB footprint?
What do folks use to get an appropriate 2mm header pcb footprint? I I used the one generated by setting a standard header to 2mm pitch with inspector, but when I looked at the gerber the pads are way...
View Article2mm header PCB footprint?
I assume you are talking about a through hole header with 2mm spacing? I checked and if I select generic header, set it to 2 pins, 2mm pin spacing and then set the hole diameter to 1.0mm and the ring...
View ArticleTo flip or not to flip, that's the flipping question
'Flip' and 'Mirror' mean the same thing in this context. It seems a bizarre omission that you can use Fritzing to lay it all out and work out what you need to do, but then it can only provide the...
View Article2mm header PCB footprint?
Thanks, yes I'm looking for a 2mm through hole header and I didn't think of doing that. It will be much easier than trying to hand edit the pads in the svg. A.035 hole (standard IC size) is .89mm and...
View Article2mm header PCB footprint?
I tend to use the generic headers for stand-ins for a lot of stuff and find that with those three settings (and multiple headers) you can make almost any foot print needed. You will end up with a crap...
View ArticleClik here to view.
Njd clone analog dub siren
Thanks for answer peter,do you think if this schematics is very dificult for start?. image.png1500x1000 36.3 KB
View ArticleQuestion about jumpers
Thanks Peter - That is what I have done. I just does not have the "look" of a jumper that makes "following" the PCB layout a easier. I will post the fzz file just for comments. It is a two board...
View ArticleClik here to view.
Njd clone analog dub siren
It is mosty standard parts available in core, so it should be fairly easy to make.The only one not in core is the 4 way switches but as luck would have it I made one for someone a while back so you...
View ArticleClik here to view.
2mm header PCB footprint?
Another useful trick I have learned . That worked perfectly, the exported footprint has .035 holes and a reasonable pad spacing unlike the default settings. Thanks again. Peter
View ArticleClik here to view.
Question about jumpers
Yep the upload worked fine. Ah the joys of single sided boards sometimes jumpers are the only answer on single sided, but in this case I think you can avoid it. Starting from the 2nd from left pin on...
View ArticleQuestion about jumpers
Peter - Thank you for the very rapid replies ... much appreciated. The jumper you see in place is not really the problem. I have two other jumpers still to be positioned. At this time they are being...
View ArticleQuestion about jumpers
Yes I see your issue. It isn't possible to tell where the jumpers are supposed to be from the drawing. You could label the pins something like j1-1 and j1-2 (for the two ends of jumper1) and j2-1 and...
View ArticleNjd clone analog dub siren
Thank you very much peter for the help provided, it has been very useful
View ArticleRename "My Parts Bin"
Well, started up Frizting and right clicked on the name of the parts bin and was able to rename it properly. On a restart all looks well.
View ArticleRotary micro switch
Hi Peter, waiting for boards with rotary SW from F. Will send you a pic of the fruits of your labor, cant wait! thank you again so much, les
View ArticleRename "My Parts Bin"
Huh! Mine still has rename greyed out when I right click it.Did you do something different this time? Peter
View ArticleRename "My Parts Bin"
Must have been from playing around in the xml file. I just started Fritzing again, and the rename is greyed out again.
View Article