Availability of 8051 parts in Lib folder
Hi guys , I ve given a project on MCS51 microcontroller architecture , can i find 8051 part library on fritzing. ?. Can i download it from the site. please give me the link
View Article16x2 I2C LCD Part
Very new to Fritzing so be gentle. I've had a look about and either I've lost the plot and its staring me in the face or its not in the standard parts bin. But, is there a 16x2 LCD that is I2C rather...
View ArticleClik here to view.
16x2 I2C LCD Part
googleing for Fritzing 1602 lcd i2c part (or ritzing 1602 lcd i2c part as I actually did ) turns up: http://fritzing.org/projects/lcd-i2c-analog-inputoutput-displayed which from only a look at the...
View ArticleAvailability of 8051 parts in Lib folder
I can't find a datasheet. If it's just an IC grab an IC, select width in Inspector, select pins in Inspector, and type part# in Inspector
View ArticleClik here to view.
Power Supply for Small Barrel
I'm looking for some help for a power supply. The unit says it is DC5V. I thought about looking Fritzing for some possible help regards the amps and other specs. I find only ones that marked as 5.5 mm...
View ArticlePower Supply for Small Barrel
I'm not sure I understand your question. Assuming that is a Uno on the bottom, it has (typically anyway) a 2.1mm barrel plug in which it wants to see about 9V to power the on board 5V and 3.3 volt...
View ArticlePower Supply for Small Barrel
Sorry, I'm looking for a power cord, plus into a wall, for the board depicted on top in the image. On the cover which covers the top board, it says DC5V on it. In order to purchase the power cord, I...
View ArticlePower Supply for Small Barrel
Ah! So you have a couple of issues: you need to know how much current it needs (solvable by giving it a supply with too much, as it will only take what it needs) and most importantly to know which pin...
View ArticlePower Supply for Small Barrel
Thanks for the reply Peter. that gives me lots to think about. How exactly are these things measured? What does the 5.5 mm mean?
View ArticlePower Supply for Small Barrel
I think that is probably the barrel outside diameter from the 2.1 connector data sheet I just pulled up. http://www.mouser.com/ds/2/393/760-765_cd-371293.pdf The inside diameter is the 2.1mm that they...
View ArticleProblems joing wires or even attaching components to wires in breadboard design
HiI am relatively new to Fritzing, so please excuse me if this is a daft question,but I have read all the tutorials etc. If I add a component. and then double click an existing wire to make a...
View ArticleProblems joing wires or even attaching components to wires in breadboard design
Try holding down the Alt key only and drag form the bend point, or drag from the connector to the bend point. Edit: Sorry, that only works on the pcb and schematic view... on the breadboard view they...
View ArticleArduino Controller PCB design
Hey there, I am using Fritzing to make my first arduino board. I have developed the PCB design but when I export them to the etachable PDF, I got eight different pdf files and their mirror files also....
View ArticleArduino Controller PCB design
Print out the PDF... What exactly are you wanting to do? Send it out to a fab house or make the board yourself...
View Article16x2 I2C LCD Part
That's the one I found too Peter. I think I'll make life easier and leave a header on the board rather than trying to wire it all in until I can work out how to produce a proper part. Thanks Alex
View ArticleArduino Controller PCB design
I am making a board myself. There are eight files. I want to take a print on a single paper. what should I do? If I print them all 8 pdfs, there will be eight pages.
View ArticleProblems joing wires or even attaching components to wires in breadboard design
If it's BB view, you right-click in the middle of the wire and Add bendpoint, then right-click one side of the wire and Delete wire to bendpoint, then add a wire starting from a component or drag a...
View ArticleArduino Controller PCB design
You don't have the print all 8 pages... you can just print current page or select the pages you want to print. If you are making a negative and using a UV light you will need to print it out on a...
View ArticleClik here to view.
Problems joing wires or even attaching components to wires in breadboard design
Old_Grey: Delete wire to bendpoint, then add a wire starting from a component or drag a remaining wire to the bendpoint. I tried that, it didn't work... It only seams to work with bendable legs...
View ArticleProblems joing wires or even attaching components to wires in breadboard design
Opps. You can physically put the wire on the bendpoint, but it doesn't connect. EDITI just realised you can't do it in real life, so why would you be able to do it in FZ BB view.
View Article