USB 3.1 type C female socket connector
I’m going to see if @steelgoose 's odd shaped board holes will work for this. In theory it may (I don’t think the mounting holes need plating). As you say the pads are to close to allow a hole to be...
View ArticleClik here to view.
USB 3.1 type C female socket connector
If I had these connectors already and was trying to make a board I would bend the tabs out and make the footprint an smd pad like the micro usb ones. Micro usb footprint
View ArticleA discussion of future direction
Out of curiosity, how far from a Release Candidate or another Beta was ver 0.93b?
View ArticleA discussion of future direction
Assuming “was” above should be “is”, it is hard to say. The new gerber code (which is the biggest change) has been backed off as not working. The development environment is now building correctly (it...
View ArticleNeed help for an Arduino connection
Thanks a lot for your answers, we could finish our work because of you.
View ArticleClik here to view.
USB 3.1 type C female socket connector
just an idea but if the part cant work because of the mounts, would it be possible to do something like this. as the part will still fit to the mount and overlap the connector (basically square off...
View ArticleUSB 3.1 type C female socket connector
@customerx, @sublimeartistry, @vanepp Well, you are right in all cases; You can’t overlap drill holes “it would probably snap the drill bits”. I just use a round hole when possible, but not always...
View ArticleApi-ms-win-crt-runtime-l1-1-0.dll Fix?
In response to "sublimeartistry" Not all of us are programmers and if we could correct the problems we would have done it already. I got the impression from previous posts that is was only a missing...
View ArticleClik here to view.
USB 3.1 type C female socket connector
it looks like using a dif program, or learning quite some more before what I want is going to be achieved this way, appreciate all your hard work guys.
View ArticleApi-ms-win-crt-runtime-l1-1-0.dll Fix?
The runtime download is certainly a requirement, that doesn’t mean that more things can go wrong though. What isn’t working now? The most common problem after the runtime dll is not waiting for the...
View ArticleESP-WROOM-32 (ESP-32S) part
Unfortunately there was more wrong than just the scaling. Some of the pins in schematic were also wrong (likely due to the pins not being in sequence) and the grounds weren’t bussed. In the end I...
View ArticleClik here to view.
ESP-WROOM-32 (ESP-32S) part
vanepp: Some of the pins in schematic were also wrong (likely due to the pins not being in sequence) and the grounds weren’t bussed. What makes them “wrong”. They work and they are connected to the...
View ArticleESP-WROOM-32 (ESP-32S) part
OK, I have created my version as a new part below which will load separate from the original. In the original schematic note that there is one too many grounds, and pins pin 15 to 19 are out of order,...
View ArticleClik here to view.
ESP-WROOM-32 (ESP-32S) part
Thanks for spelling it out for me. The extra ground in the schematic was labeled wrong as you say. You changed it from GND in schematic and RTS everywhere else to CMD everywhere which goes better with...
View ArticleClik here to view.
ESP-WROOM-32 (ESP-32S) part
sublimeartistry: Last thing is my part has nicer mouse overs then yours. When you mouse over any of my pins they just say what the label is. With yours it shows Fritzing pin number which is of zero...
View ArticleClik here to view.
V-cut or panelization
After setting multiple circuits on the large board, Some options are: Make the board and cut with razor knife (make several score lines). If you have access to a Milling machine, mill the cut and/or...
View ArticleA discussion of future direction
I don’t know if this belongs here but if you’re talking about future features I believe the parts bin needs a radical rethink. It must have worked as a POC with a very short component list but I’m...
View ArticleClik here to view.
A discussion of future direction
obroad: I don’t know if this belongs here but if you’re talking about future features I believe the parts bin needs a radical rethink. Sure, we are discussing future directions and volume isn’t so far...
View ArticleClik here to view.
PC817 Optocoupler
I’m learning how to make parts and have made PCB layouts for two PC817 surface mount packages which are missing from fritzing. My issue is that the sizing is as per the datasheet in Inkscape but seem...
View ArticleClik here to view.
PC817 Optocoupler
I’ll see if I can help. The first thing I notice is you have all the Inkscape labels set and that is not needed. It will not hurt anything but Fritzing only looks at the ID which you have also set....
View Article