Clik here to view.
Positioning the Arduino headers on a PCB board
Ah! my mistake then, I figured you already had edited a part (which is what you will need to do to make a shield part). Your life just got a lot more complicated because you are descending in to parts...
View ArticleConception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
merci pour votre réponse . Mais je ne sais pas faire d’esquisse . Ce n’est pas moi qui est fait le schéma de principe . Les capteurs ne seront pas tous droit , il peuvent être soudés un peu en biais...
View ArticlePositioning the Arduino headers on a PCB board
Are you saying that you have positioned parts in the PCB view, if it is then upload the sketch, ie the .fzz.
View ArticleClik here to view.
240V ac power supply source and a bulb
I am doing a smart bulb project and I am using fritzing for my circuit design but l could not find a 240V ac power supply source and a bulb. Can anyone help me with that please. The picture is not...
View ArticlePositioning the Arduino headers on a PCB board
OK - here is the .fzz I have not used the std arduino shield as I am running a ton of traces thru the two IC’s and on to 4 Ethernet plugs going to the leds I am driving. I will be supplying external...
View ArticleConception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
rampe capteur accordéonUntitled Sketch.fzz (47.7 KB) J’ai rajouté un capteur !!!
View ArticleConception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
I kind-of felt that he wanted help making a sketch in FZ. If you want to use BB view as the master for connections - most people use SCH view -, you must make the BB view correct. Wires touching in BB...
View ArticlePositioning the Arduino headers on a PCB board
They look pretty close - I can see slight non concentricity -, but it should be fine because the tolerance of the holes will allow for some movement. The double check is to print out the gerber and...
View ArticleClik here to view.
240V ac power supply source and a lamp
New to Fritzing but hooked. I am doing a smart bulb project and I am using fritzing for my circuit design but l could not find a 240V ac power supply source and a bulb. Can anyone help me with that...
View Article240V ac power supply source and a bulb
As always google is your friend. A search for “fritzing part light bulb” (and looking in the images section) turns up this:...
View ArticlePositioning the Arduino headers on a PCB board
Thx I’m surprised I cannot use the location of each header to precisely position the parts - ? I would have thought a set of 4 co-ordinates for each of the required headers would ensure no problems. I...
View ArticleClik here to view.
Positioning the Arduino headers on a PCB board
I think the coords in FZ only has a 4 or 6 thou resolution, hence why it jumps when you enter numbers. Everybody usually leaves the Arduino on the board even though it’s not part of a shied. EDIT -...
View ArticlePositioning the Arduino headers on a PCB board
Old_Grey is a better bet on board issues than me. I rarely do boards. My normal method of setting coords is to edit the underlying svg file rather than using Fritzing. As Old_Grey noted the real test...
View ArticlePositioning the Arduino headers on a PCB board
OK - all good points. I will try the gerber files and proceed from there. appreciate the help
View ArticleClik here to view.
Conception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
The first thing we needed is a proper part for the sensor (thanks for the data sheet!), so I made one. A3144 Hall Effect Sensor_.fzpz (6.7 KB) It is on .05 in centers and 4.17mm wide. Now we need to...
View ArticleClik here to view.
Drawing Resource - Alternative to Inkscape
I often use OP-Amp’s - usually LM358, MCP6002 and MC1458. These are DIP8’s with similar Pinouts and Performance. Most of the time, I use only one Channel, thus I made a Part without the 3-unused pins....
View Article1 of 2 nets routed
Thank you for the help. I feel relieved now. Thanks for this tip! Sorry for my late response. I appreciate your gesture and support for me.
View ArticleConception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
It’s a bit hard to follow what’s going on because the translation isn’t great, but I think we need the spacing of the magnets. Then again there is a thing with switches. I read 305mm, then something...
View ArticleClik here to view.
Conception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
Old_Grey: I read 305mm, then something 335mm, it all gets confusing. 305m is the max size of the board, it is going in to a space that is 335mm long as I read it. The extra space has something else in...
View Article