Clik here to view.
Axial (electrolitic) capacitors, are there any?
Try this one ( a google search for “fritzing part axial electrolytic capacitor” is your friend, I remembered making this one but not where it was …): TVX1V101MAD Electrolytic Capacitor, Axial Leads...
View ArticleConnection Error
Hi Old Grey and vanepp, I have attached the .fzz. Thanks Hutzpah Weather station_sensor error.fzz (38.4 KB)
View ArticleConnection Error
The gerber only shows a bottom layer, which is ok if you etch your own PCB, but for production I guess it should have both. Looking at the BMP280 it looks like the copper1_1_ is labelled wrong, but...
View ArticleConnection Error
Indeed copper1 is misspelled along with breadboard. You will need to delete the old part (using delete minus to leave the traces) then shutdown fritzing to get rid of the old part entirely, then load...
View ArticleClik here to view.
Stepper Motor Control Circuit using SN754110 H-Bridge
This is the Motor Circuit I use for Stepper Motors It’s not really a ‘Part’ but, it can be Copied&Pasted into another circuit…_ Stepper_PH.fzz (24.7 KB) Stepper_2PB.fzz (24.6 KB) Stepper_Combo.fzz...
View ArticleClik here to view.
LM239 Quad Comparator
The LM393N is an 14 pin DIP IC chip. It is commonly used in ADC converters, Comparison circuits, Op-amps and wave-forms. LM239_IC_DIP_14_300mil.fzpz (9.1 KB)
View ArticleClik here to view.
[sharing] custom designed NRF24 module with PIFA
Hello, this is my design of custom antenna nRF24 module. for better detail please see the achievement . based on schematics from Nordic company replaceable with nRF24-module (nRF24L01) from market ,...
View ArticleConnection Error
Thanks very much Peter for your help. I did as instructed from your post, and it is all working perfectly. Hutzpah
View ArticleClik here to view.
LM239 Quad Comparator
Fairly nice job, schematic however is fairly messed up. test-Sketch_schem.png585x1932 73.2 KB The top one in this png is your part. Note the pins are not aligned on the .1 grid and the pin numbers...
View Article[sharing] custom designed NRF24 module with PIFA
It would be more useful to make these antennas as parts so people could just add them to their module of choice. That would also cut down on the vias which I expect are probably causing reflections...
View ArticleElectret Microphone Amplifier - MAX9814 with Auto Gain Control
Anyone know if this exists in the library and if so what its called? https://www.adafruit.com/product/1713 If not, anyone fancy making it? Thanks Brian
View ArticleElectret Microphone Amplifier - MAX9814 with Auto Gain Control
It’s on the page you are linking to.
View Article[sharing] custom designed NRF24 module with PIFA
at my design I usually left the start and end via so I can drag the entire antenna together, and after locating I’ll remove the vias. I think people can experiment their own antenna design and not by...
View ArticleElectret Microphone Amplifier - MAX9814 with Auto Gain Control
Well there is something new i have learnt, i never new they had there own library Thanks Brian
View ArticleElectret Microphone Amplifier - MAX9814 with Auto Gain Control
I would say the majority of FZ parts aren’t stored here, so it always wise to Google for them and just add fritzing to the search. You can usually spot them quicker in the image search part.
View ArticleLM239 Quad Comparator
Wow Peter! Thanks so much for taking the time to look this over, make the corrections and for encouraging me to post it on GitHub. I’ll see if I can figure out that whole process now. Thanks again.
View ArticleConception de 2 circuits imprimés avec capteurs à effet hall , et une carte...
Hello peter I ordered my 2 circuits at Asler and I will receive longues pin headers, I can solder the wires on pins headers with a heat shrinkable sheath....
View ArticleClik here to view.
TP4056 Charger board fault?
Hi Guys Need some advice, I used the TP4056 Charger board found here http://forum.fritzing.org/t/tp4056-charger-board/4795 I’ve had some PCB made and they don’t fit, fits one way but where the dual...
View ArticleClik here to view.
TP4056 Charger board fault?
This problem provides a ‘Perfect’ example of using my Woof app. The pin spacing is correct ≈2.54mm pitch. But, the background image it’s sitting on does not have 2.54mm pitch. Looks good at short...
View ArticleClik here to view.
Load Cell Sensor Part
Sweet. I do not usually make Fritzing parts so I was bound to be missing something. I’ll have to take take some time to look into the script. I compared the two parts and I will keep that in mind of...
View Article