DC Barrel Jack Adapter Male
This could be even uglier, as the part on top I am using is stripboard. Once I have the basic 'lower' part, I'll try a few permutations and get back to you.
View ArticleDC Barrel Jack Adapter Male
You may be able to make a new strip board part (probably the same way I did breadboard) and change its family name to something other than breadboard. I think it is the family name that trips the...
View ArticleDC Barrel Jack Adapter Male
The strip boards have a functionality where you can connect the holes together... If you take the function out of it and make it a part, I doubt if any of that will work. You may be able to save the...
View ArticleSpurious unrouted connections in BB view
What do you mean. If you want to plug a cap into the UNO directly you have to grab the bendable legs and pull it to the header, because it doesn't snap to some of the headers.
View ArticleSpurious unrouted connections in BB view
Both just dragging and dropping the part and dragging the bendable legs seem to fail - you get the 'green light' but status still shows unrouted connections.
View ArticleSpurious unrouted connections in BB view
Oh yeah, the status goes weired. I've got 4 green dots and it says 0 of 4 nets routed.
View ArticleSpurious unrouted connections in BB view
But if you use wires it works fine. I want to create jumper plugs to insert into Arduino (and other) headers, but currently you get these routing funnies. It works fine with a plain breadboard.
View ArticleSpurious unrouted connections in BB view
I just checked PCB view and it says 2 of 6 nets routed. After I made the 4 ratsnests solid traces, it says Routing completed. I went to BB and put actual wires in instead of direct connections, and it...
View ArticleSpurious unrouted connections in BB view
As far as wires in breadboard view go this was my finding also. Doing that makes a mess of breadboard view though. Unfortunately, I do not understand the routing algorithms well enough to say what the...
View ArticleClik here to view.
Spurious unrouted connections in BB view
sgparry0407: At a superficial level, it seems to me that if you stick a male connector in female connector, it should count that as fully connected, but there may be reasons that is bad. I think its...
View ArticleSpurious unrouted connections in BB view
Not sure; the breadboard itself works fine - it comes up with 'no connections to route' if you plug in the legs into unconnected holes; I suspect there is some magic code in there to ignore such...
View ArticleClik here to view.
Transformer VB 1,5A 9V
VB 1,5/1/9Short circuit proof PCB transformerPDF specsVB1,5-1-9.fzpz (5.9 KB)
View ArticleClik here to view.
Spurious unrouted connections in BB view
To avoid trying to decipher the code, I tried old versions - this has been a bug since as far back as at least 0.8.2b
View ArticleClik here to view.
Spurious unrouted connections in BB view
Have you (or anyone else willing to admit to it ) compiled the latest source tree to try and see if any of these are fixed? I'm intending to try that once I finish getting a script together to post...
View ArticleSpurious unrouted connections in BB view
Sounds like you've made a real breakthrough on the scripts - which is fantastic.No, I've not compiled yet. I doubt very much given the number of commits we are seeing currently, that there is a fix...
View ArticleClik here to view.
Looking to pay someone to create a large part
Despite the long silence there is in fact progress this project below is the current Fritzing part of this project. It turns out it can't be a single part (at least not if we want schematic to work at...
View ArticleHelp, subversion archive lost
Hi,Hoping @fabian / @fa1 might see this...One of the consequences of the googlecode shutdown is that the subversion source is no longer accessible. I have managed to rescue the git source after much...
View ArticleL9110 H-bridge module
I'll try to fix the connection between pins a wires.Regarding non assigned pins, those two pins are terminal clamps, not connected to the PCB. How do I assigne them, so that they aren't depicted on...
View ArticleHelp creating a PCB
I have all of the Adafruit products in my parts bin and both these items are in there, You can download from here https://github.com/adafruit/Fritzing-Library Then open the fzbz file with Fritzing.
View ArticleClik here to view.
Search function in the parts view does not work
The issue is still valid,Please note the attached pic, in case of:* Fritzing V0.9.3, on windows 7, 32 bits, "Parts Search" doesn’t open the search box* Fritzing V0.9.2, on windows 7, 32 bits, "Parts...
View Article