Clik here to view.
4 x 5V to 3.3V logic level converter
This is a case where it was easier to fix the problem and then tell you what I did. Schematic here is the main problem (although there are others as well): schematic: group id g7 to id schematic to...
View ArticleClik here to view.
Schematic to breadboard layout
IMG_6587.JPG3024x4032 2.46 MB Okay I think I understand you, the reason why I'm asking about a mega is because I still want to add a few rgb LED's the light up different colours and also I need to...
View ArticleClik here to view.
Schematic to breadboard layout
The pedal that you referenced only has two wires coming out of it (its a mono jack thus two wires). I think the "polarity switch" they refer to changes the switch contacts from normally open to...
View ArticleCant get my parts to load properly after creating custom images
Thanks peter, i understand what youve said. If possible do you have the part names that match as closely so I can work from them? Appreciate the support
View ArticleCorrection for the RioRand_LM2596 from core (somewhere!)
I have a couple of these boards. I added pins, to add it to a perf board. The pin holes do not line up with standard holes. I ended up having to do some creative soldering to make the pins fit, and...
View ArticleSchematic to breadboard layout
Okay so I think I'm going to go down the jack socket route. I need 10 pedals which will cost me £130 and I don't want to go stripping the plug of to void warranty. So I was thinking of getting these...
View ArticleSchematic to breadboard layout
I did find this tutorial online, not sure if it's helpful but I think it says a little bit about what each wire is inside the jack lead?...
View ArticleSchematic to breadboard layout
I have read a review about the pedal on amazon saying be careful the polarity can match sometimes also on this website https://www.sweetwater.com/store/detail/DP2Pedal it says that it's normally closed
View ArticleClik here to view.
Cant get my parts to load properly after creating custom images
There isn't really anything that I see that is that close, here are a couple of choices that may help: relays: I want to include some latching DTDP relays... but oh dear Try this and see if it does...
View ArticleClik here to view.
Correction for the RioRand_LM2596 from core (somewhere!)
That is part of the correction I have a couple of the actual modules and changed the Fritzing part to have the correct (not .1 aligned) pins in both breadboard and pcb by measuring them with vernier...
View ArticleClik here to view.
Schematic to breadboard layout
jovid196168: Okay so I think I'm going to go down the jack socket route. I need 10 pedals which will cost me £130 and I don't want to go stripping the plug of to void warranty. So I was thinking of...
View ArticleIs it possobile to make a part that can have daughter boards attached
Thanks a lot, I will take a look at it. Jeffery
View ArticleSchematic to breadboard layout
Okay so all these will work then? I'm actually planning to keep the wiring inside. All these electrics I want to encase in a housing so tripping over the wire and putting stress on the cable shouldn't...
View ArticleSchematic to breadboard layout
Yep the connectors shown should work. They connect exactly like your current switches there are two sets of pins connected together (giving you two connections) one goes to ground and the other to the...
View ArticleSchematic to breadboard layout
Okay only thing I don't know is the actual size of the jack plug it just doesn't say anywhere. I'm guessing it's standard, when you say change the software do you mean about the pedals polarity being...
View ArticleClik here to view.
Cant get my parts to load properly after creating custom images
Thanks I downloaded that Relay and edited it to match my initial version, does this seem correct now? dropbox.com - Fritzing Parts.zip Shared with Dropbox I wasn't sure about the PCB as my initial one...
View ArticleSchematic to breadboard layout
I'm still confused how to wire these jack sockets but I found a tutorial explaining it here http://www.ampmaker.com/se-5a-chassis-wiring-part-1-962-0.html
View ArticleNodeMcu V3 parts library
I'm trying to find a fritzing part for the LoLin NodeMcu V3. I initially used the https://github.com/roman-minyaylov/nodemcu-v3-fritzing library. However, after production I found out that the pin...
View ArticleClik here to view.
Schematic to breadboard layout
jovid196168: Okay only thing I don't know is the actual size of the jack plug it just doesn't say anywhere. I'm guessing it's standard, when you say change the software do you mean about the pedals...
View ArticleCant get my parts to load properly after creating custom images
Inkscape won't open the svgs in your latest zip for me. It would be easiest if you export the part directly from frittzing (assuming you are now getting a part in Fritzing of course). To do that right...
View Article