Panalize (divide) pcb with overlapping holes?
I think this depends on the fab house, so it's best to ask them - maybe have an example design ready to show them.
View ArticlePanalize (divide) pcb with overlapping holes?
They support vcuthttp://support.seeedstudio.com/knowledgebase/articles/912045-v-cut-rules but i read somewhere they manually check before proces. Some houses are not amused with overlapping holes. It...
View ArticleSchematic to breadboard layout
I've been looking into led's shift registering with push buttons. Can't seem to find anything online. But I've been suggested to now use Bi-Colour LED which light up red and green when you reverse the...
View ArticleMojo FPGA v3 from Embedded Micro
Peter, I have updated the GitHub repository with the latest (working) part file. I had mistakenly named each internal pin on the header layer (not the connector layer) to be connectorXpin, so when the...
View ArticleMojo FPGA v3 from Embedded Micro
The pins of the board line up on a perfboard. That's how I originally calculated how many pins to use as distance. I think the problem was that I was working using the Pixel UOM instead of inches, so...
View ArticleClik here to view.
Mojo FPGA v3 from Embedded Micro
I just got the Eagle files from Embedded Micro for their Proto Shield. I've removed all of the vias so that only the holes for the headers remain (in addition to some wires that run into the board for...
View ArticleUnits on font-style in svg part files do not export as svg
I read that reference before, and even saw the unitless reference. It did not click that was going to cause a problem. Looks like the real problem (other than the export not handling the units), is...
View ArticleUnits on font-style in svg part files do not export as svg
From memory, which isn't very good, you don't have to remove all the px's, just 2 in each text group. It's some where in my video series.
View ArticleSchematic to breadboard layout
Alright, yeah that makes sense my bad. I will try that after. Got ten pedals set out. I haven't set anything to the tenth pedal yet as I need to write and figure away how to use midi bank to like...
View ArticleSchematic to breadboard layout
There are two kinds of bicolor leds. One has two leads and one has three. You likely want the ones with three leads (which is to say the same as your common cathode leds) as they are a bit easier to...
View ArticleClik here to view.
Mojo FPGA v3 from Embedded Micro
cerkit: Thanks, I don't think Fritzing was designed with Illustrator in mind, so I've downloaded Inkscape and may try to learn that (since that's what most of the tutorials on the web use). Actually...
View ArticleMojo FPGA v3 from Embedded Micro
This Eagle2Svg script in Eagle can also export everything in monochrome. Would that help any?
View ArticleMojo FPGA v3 from Embedded Micro
No, the current svg is fine as Old_Grey noted it has the xy coords of all the elements and I can position them from there. Pcb is done I'm having a quick bash at schematic. Peter
View ArticleMojo FPGA v3 from Embedded Micro
How does your final SVG look for the square pads? I have modified the Eagle2Svg script in Eagle to generate a more sensible file (using your specifications from above). I just need to know how to...
View ArticleMojo FPGA v3 from Embedded Micro
The square should look like this <rect fill="none" stroke="rgb(255, 191, 0)" id="square" y="41" stroke-width="20" gorn="0.3.0.0" height="58" x="41" width="58"/> for a standard .038 pad (which is...
View ArticleAPA-102-2020 - the ultimate smd addressable led
Thanks Peter, I have used Inkscape before. I will try to resize there.
View ArticleSchematic to breadboard layout
Right well I have got the pedals all working, had to change the HIGH's to LOW's and the LOW's to HIGH's. All good now, when a pedal is pressed midi monitor says note on and then note off. now its down...
View ArticlePanalize (divide) pcb with overlapping holes?
=== update === answer on my question is give to me by accidentally. I ordered a 7-segment digit panel pcb with 3 holes for mounting on the left and righst side (middle and corner) for screws. Got a...
View ArticleV-cut with FRITZING - possible?
I also interested. I think we need to edit the gml file. Is someone could give a example how to enter a v-cut line in the gml file, let's example of a 100mmx100mm board from left to right (and up to...
View ArticleMojo FPGA v3 from Embedded Micro
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
View Article