Clik here to view.
RDM6300 RFID module
Again by and large an excellent part. As Old_Grey noted the board needs some work on copper0/copper1 and silkscreen, I chose to have a bash at the antenna part.Below is an fzz file with your original...
View ArticleMylar capacitors (For PT2314)
I'm trying to make an arduino shield for a PT2314 audio processing ic. http://pdf.datasheetcatalog.com/datasheet/PrincetonTechnologyCorporation/mXuyuxw.pdf it calls out for Mylar Capacitor for...
View ArticleMylar capacitors (For PT2314)
A quick look for mylar caps on digikey indicates the pin spacing is .2 in so select a ceramic cap from core and with it selected in the sketch in Inspector change the package from 100 mil (.1 in) to...
View ArticleQSOP16 to DIP16 300mil adaptor
I use a footprint that had long pads so that you can fit anything from QSOP to anything wider on the same pitch. The DIP is std 300mil width like on an IC.QSOP16 to DIP16 300mil.fzz (11.9 KB)
View ArticleMylar capacitors (For PT2314)
so simple. thanks. as you can see, i'm very new at this thank you!
View ArticleCannot make PCB
I am very new with Fritzing.I want to make pcb of a guitar preamp with a schematics.But i cannot make the PCB.Please any one help me to make the pcb with a 3"x1" board.Fritzing file is...
View ArticleClik here to view.
Cannot make PCB
I guess you want to organise the placement of parts in PCB. Spread the parts out and put ICs in the middle, because it connects on all sides, and click on a pad and all the connected pads will turn...
View ArticleClik here to view.
I'm looking for cc40192 and cc4511,thanks!
I searched them in the bin ,but there's none.I am a beginner so that's hard for me to create them on my own . Can u help me out..plz..
View ArticleI'm looking for cc40192 and cc4511,thanks!
If they have a generic IC footprint just grab one out of the CORE bin, change the number of pins in Inspector, and type the part# further down in Insp.
View ArticleCannot make PCB
Why not? They will fit for me. It is highly likely this isn't correct since I just changed the pcb size in inspector to 25.4mm by 76.2mm (1*3 in) then dragged parts around until they all fit. In...
View ArticleI'm looking for cc40192 and cc4511,thanks!
A google search didn't turn up either as a Fritzing part so Old_Grey's suggestion is the correct one. Both are available as 16 DIP so 2 generic ICs with 16 pins and change the pin description with...
View ArticleI'm looking for cc40192 and cc4511,thanks!
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
View ArticleClik here to view.
I'm looking for cc40192 and cc4511,thanks!
Thanks for replying!And all i need to do is editing two generic ICs with 16 pins(I can find HEF4094 in the bin,is it a generic one?) , and changing the pin description to match the correct pins? So...
View ArticleI'm looking for cc40192 and cc4511,thanks!
thank you! if u don't mind , check my another reply below vaneapp's.
View ArticleClik here to view.
I'm looking for cc40192 and cc4511,thanks!
good1uck: (I can find HEF4094 in the bin,is it a generic one?) While it isn't generic, it will work fine for what you want to do. Just edit it with the parts editor and change the pin labels to match...
View ArticleRDM6300 RFID module
I apologize for my English. It is very weak and so it may happen that I understand something wrong ...I thank you for valuable and comprehensive comments. I will remember it when I'm going to do...
View ArticleI'm looking for cc40192 and cc4511,thanks!
There are billions of different parts so there will never be a specific part for every one, but there are less PCB footprints because they standardised part sizes. You have one machine stamping out...
View ArticleRDM6300 RFID module
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
View Article