SVG circles don't match Fritzing Circles
Are the pads that work "circle", and the pads that don't work "path" If you can't figure it out upload it with the 7th button and someone will have a look.
View ArticleSVG circles don't match Fritzing Circles
XFW-HX711.fzpz (18.4 KB) No. They are both "path".
View ArticleClik here to view.
SVG circles don't match Fritzing Circles
zerox21: SVG, image is hard to see --> He did upload the svg. If you right click on the end of the arrow above and save image to file you will get his svg. The forum is rendering it there, just...
View ArticleClik here to view.
SVG circles don't match Fritzing Circles
Turns out I was maligning core parts unjustly , in fact I had loaded this part (from elsewhere on the net) and mistakenly though it was in core. Grove Ultrasonic Ranger.fzpz (9.9 KB) At least one (and...
View ArticleClik here to view.
Question about jumpers
vanepp: As a final test to make sure all is ok, export the gerber (which is what the fab will use to make the boards) and use a gerber viewer (I use gerbv from the geda project, but there are others...
View ArticleQuestion about jumpers
I think that pwr connector has flat pins that require a slot, and last time I tried FZ couldn't do slots, at least not in the drill.txt file, so the parts has to have big holes because of the large...
View ArticleQuestion about jumpers
With the warning that I don't often do boards (and thus you would be best to get one of the other folks here to look this over) here is how I would change your board and why: MRK1000 6_20_17_peters...
View ArticleClik here to view.
Question about jumpers
On to the lcd board . The major problem is you forgot to set single sided and all the traces were routed on the top layer. I also suspect that you could and probably should delete the traces...
View Article[NEW PART] Breadboard view totally black
I am new to electronics, but I have great interest to learn new things of electronics. The main thing which is used in electronics is breadboard. It is a rectangular plastic board with a bunch of tiny...
View ArticleClik here to view.
Question about jumpers
If you are good a puzzles you can weave traces around the back of stuff.
View ArticleSVG circles don't match Fritzing Circles
Is there a "library" SVG somewhere that has a collection of typical pads, etc. so that I can just copy paste what I need instead of reinventing all this stuff that has probably already been created...
View ArticleSVG circles don't match Fritzing Circles
After drawing the PCB again with "circles" everything works. Thanks for the help.
View ArticleSVG circles don't match Fritzing Circles
I usually use the generic IC from core and set its number of pins to match the number of connections I need. That creates the appropriate pins,their connections and the pads in all three views and can...
View Article[NEW PART] Breadboard view totally black
Start fritzing and select breadboard view. You will then see a virtual copy of such a breadboard and can use it. To see examples, download a sketch (an fzz file) from the projects tab on the main...
View ArticleClik here to view.
Question about jumpers
Peter and Old Grey - Thanks again for the input. I have attached two files for review. One is the actual stereo jack plug showing the three pins and reinforcing legs that relate to the PCB. The...
View ArticleQuestion about jumpers
Old Grey and Peter ... and others After reading some other posts and seeing the Parts Editor video from Old Grey ... I thought I would try to edit the Stereo plug I am using in this project. I created...
View ArticleQuestion about jumpers
If you are home etching put 0.4mm via on every pad so that it centers the drill very accurately, because if you use the std 0.9mm hole the drill can start off-center. Via size is adjustable in the...
View ArticleClik here to view.
Question about jumpers
jbund65: I do not know what the default hole and ring size for the "jumper pads" I don't either, but I said "that will be easy, just edit the pcb svg in core and look". Wrongo! there doesn't appear to...
View ArticleClik here to view.
Question about jumpers
Unfortunatly parts editor is a work in progress and at present can't make those kind of changes. To do so you would need to save it as a new part (without any changes except maybe to the metadata to...
View ArticleClik here to view.
Question about jumpers
Thank you both ... Peter and Old Grey I have some graphic experience and may want to do some editing of parts in the future. Your library is pretty darn good for the majority of users I imagine! My...
View Article