Clik here to view.
Question about jumpers
This has been good! Two new ways to deal with the problem. I must admit if I ever manage to finish the python script to fix svgs and check fpz files, I'm thinking a script that can do stuff like this...
View ArticleClik here to view.
Parts modification for power plug
jbund65: The following message is mentioned as a possible problem when using this power connector: Would you please compare this or offer suggestions to which power connector image I should use to...
View ArticleDouble copper pad not showing on Gerber viewer
That explains why it worked when I changed the PCB, because I used a PCB so big that all the pads were on the PCB.
View ArticleRaspberry Pi Zero Fritzing Part
Can you update the part file so the pins are spaced properly?
View ArticleRaspberry Pi Zero Fritzing Part
I could if I saw anything wrong with it. However the one available from the core parts bin by searching for "raspberry pi zero" is correct as far as I can see so you should use that. I might be...
View ArticleRaspberry Pi Zero Fritzing Part
The spacing of the gpio pins is too small. If you open the regular raspberry pi and the zero, you will see the size discrepency
View ArticleRaspberry Pi Zero Fritzing Part
So it is (didn't look close enough). They look to have used 2mm instead of .1 in pcb. I'll post a corrected part in a bit. Peter
View ArticleRaspberry Pi Zero Fritzing Part
I owe you a beer. This has been an all day thing trying to figure out a work around.
View ArticleClik here to view.
Rotary micro switch
IMG_20170624_185650.jpg2592x1944 1.33 MB Hi Peter, fits like a glove!!! thank you so much again Les
View ArticleClik here to view.
Rotary micro switch
Good to see! You are most welcome, if you are familiar with parts creation that isn't a big job, but becoming sufficiently familiar with parts creation is a big job . Peter
View ArticleRaspberry Pi Zero Fritzing Part
Here once I can get one to work :-). This is much more screwed up than I first thought. I replaced the pcb svg completely and it looks like breadboard is managing to carry a translate over in to pcb...
View ArticleClik here to view.
Raspberry Pi Zero Fritzing Part
Progress! I replaced the other 3 svgs (other than pcb) with the pi 3 versions and now pcb (without any changes) is properly scaled, it still isn't exporting correctly but for sure breadboard is also...
View ArticleRaspberry Pi Zero Fritzing Part
Thanks Peter, I spent all day putting this pcb together, and when I test printed it I had a head to desk collision. I'm glad you are getting it done correctly. I'm using the zero w which is the same...
View ArticleClik here to view.
Raspberry Pi Zero Fritzing Part
Here is a part that mostly works (with the warning that I don't know why it works ). All I did was group the components in breadboard because with only the connector present it worked, indicating...
View ArticleRaspberry Pi Zero Fritzing Part
Yeah, looks better. I did an export to gerber. Take a look at the copper. There seems to be a slight offset of the gpio pads. It looks as if there is 2 pads, with one slightly ofset down and to the...
View ArticleClik here to view.
Clik here to view.
Raspberry Pi Zero Fritzing Part
That's odd. I just downloaded the file I uploaded (to make sure I had uploaded the correct one last night ) and cleared my gerber directory to make sure no old files in there, then loaded Raspberry Pi...
View ArticleRaspberry Pi Zero Fritzing Part
Yeah, I was wondering why someone wouldn't have just copied the part of the old pi file that works, onto the new svg. Seems like that is the easy way to go.
View ArticleClik here to view.
Raspberry Pi Zero Fritzing Part
I think the underlying problem is a fritzing bug of some kind. I haven't seen anything in the original file (other than it doesn't work ) that looks wrong, it may not be optimal but it should have...
View Article