Raspberry Pi Zero Fritzing Part
Why not just use the 40 pin header part and draw the silk screen footprint around it. For PCB purposes that is all you need for production to begin right?
View ArticleRaspberry Pi Zero Fritzing Part
That's essentially what was done in both cases. Part of the difficulty is that dual row header generation isn't currently working so we have to find another source (I used the pi 3) and then draw the...
View ArticleClik here to view.
Raspberry Pi Zero Fritzing Part
Yeah it does that thing where it duplicates pads and offsets them, like it did with my TO220, when you change it in Inspector to "bottom" Never found the problem so I just started again. TO-220 FET-N,...
View ArticleRaspberry Pi Zero Fritzing Part
Thanks, that reproduces it for me as well. I'll have a poke at it and see if I can figure out whats going wrong (since a generic connector doesn't do that). Peter
View ArticleRaspberry Pi Zero Fritzing Part
In my opinion the schematic sucks! So I re did it. Now the pins in schematic match the pins in breadboard, the power pins have moved to their position on the GPIO connector (rather than stacked on top...
View ArticleRaspberry Pi Zero Fritzing Part
And another one bites the dust! The problem with the offset pads in pcb turns out to be a damn translate in copper0 that wasn't in copper1. Getting rid of the translate fixes the problem when the zero...
View ArticleRaspberry Pi Zero Fritzing Part
I love that you numbered the pins in the schematic view also. Much easier to connect. You deserve a medal for this.
View ArticleCannot load Parts
I have Fritzing installed on my Mac 10.12.5 running Version 0.9.3 (b5c895d327c44a3114e5fcc9d8260daf0cbb52806 2016-04-19) Cocoa [Qt 5.6.0] I use Fritzing infrequently and started on a new project. I do...
View ArticleDouble copper pad not showing on Gerber viewer
Dear Old_Grey and Peter, Thanks for your responses.Strange that it is not truncating.... The second pad does not have to be against the edge of the PCB, so i moved that more inwards and now the pad...
View ArticleClik here to view.
Raspberry Pi Zero Fritzing Part
Self interest I have a zero sitting on the desk beside my keyboard, and I wanted a better schematic so everybody wins. I'll probably ask in parts-help what has been done in the past with incompatible...
View ArticleClik here to view.
Cannot load Parts
While I'm on Windows not a Mac, the "Unable to open temporary file" sounds like a file permissions problem somewhere (unfortunatly fritzing isn't very good at telling you what file it is unhappy with...
View ArticleGround plane erstellen, aber wie?
vorab: ich bin wohl auf dem neuesten Stand 0.9.3b.64.pcmein erstes pcb layout ist bis auf die Masseverbindung fertig und der design check meckert auch nicht. Einzig und allein es ist das Netz GND...
View ArticleClik here to view.
Procedure to make incompatible parts changes to core parts?
In this thread: Raspberry Pi Zero Fritzing Part Self interest I have a zero sitting on the desk beside my keyboard, and I wanted a better schematic so everybody wins. I'll probably ask in parts-help...
View ArticleClik here to view.
Cannot load Parts
Not sure how much help it will be ... but I am on a Mac as well 10.11.16 El Capitan running Fritzing 0.9.3 as well. I would do the obvious and restart the Mac and perhaps reload Fritzing. I am...
View ArticleRaspberry Pi Zero Fritzing Part
That's a hard one because FZ will tell you there is an updated part, and if you switch it all the connects in SCH will be labeled differently. If you don't update it will stay with the old one.
View ArticleClik here to view.
Cannot load Parts
If you are comfortable executing unix commands from a command prompt window (because I don't know enough about Macs to tell you how to get it in finder ) the output from a ls -lR ~/.config/Fritzing...
View ArticleRaspberry Pi Zero Fritzing Part
I'm hoping there is a happy medium somewhere, such as rename the new parts so they can co exist or mark the original ones as obsolete (which there is a directory of) so old sketches will get the old...
View ArticleClik here to view.
Ground plane erstellen, aber wie?
While I know almost nothing about ground fills (and don't read german, but google translate does ) this has come up before for instance here: Do I need ground fill and if so how do I do it? I've said...
View ArticleFinal review before ordering
Peter, Old_Grey and others - Thanks again for all the help with the two boards I have been working on. I think I am ready to order, and will be using Fritzing. The seamless process is worth the time...
View ArticleClik here to view.
Final review before ordering
Hate to be donny downer but a few issues: you actually don't need the mini contactor on the main board. It would have the same effect (and be easier) to connect the ground of the 2nd wall wart to...
View Article