Clik here to view.
RJ11-6p6c pcb socket
Hi Peter, finally managed to get the board prepared using the Molex RJ11 Jack_top. What I'm worried about is that pins of the jack are short circuit due to maybe too large soldering ring. I have...
View ArticleRJ11-6p6c pcb socket
Let me poke at it a bit, I just copied the pad size from the sparkfun part (because the data sheet was silent on pad size) and it looks like the part I used has a smaller pin spacing (which I find odd...
View ArticleRJ11-6p6c pcb socket
When I Gerbv it the mask overlaps, but the pads have a fine 7mil gap between them.
View ArticleRJ11-6p6c pcb socket
Try this one instead. I fixed a couple of problems, there was a translate in copper1 (which I just discovered a couple of days ago breaks putting the part on the bottom of the board), the holes were...
View ArticleClik here to view.
RJ11-6p6c pcb socket
Peter, perfect! Many thanks Molex_Rev.png1168x672 39.9 KB Ready for production and logging pool temperatures using DS18B20 probes: File 29-06-2017, 08 18 06.jpeg3024x4032 1.48 MB RgdsDick
View ArticleCan I pay you to do my fritzing?
I need a round layered pcb made. Id like someone with excellent electronics knowledge to reply with an email. It is very simple, I think maybe, ten connections from a drv8833 to a feather rfm95. Hard...
View ArticleProcedure to make incompatible parts changes to core parts?
Well I suppose the answer to that question is no... There can be no two parts with the same Variant name... even if you create a new part and save it with the same Variant name, Fz with add a...
View ArticleClik here to view.
Procedure to make incompatible parts changes to core parts?
Thanks, I figured this must have come up before and there was a procedure that I just didn't know. I'll do updated versions of all the RPIs and submit them and see what happens . Peter
View ArticleProcedure to make incompatible parts changes to core parts?
btw, although they are almost identical, you have two RPi Zero's (RPi Zero and RPi Zero-w). The w stands for wireless which has builtin WiFi. It also has a couple of minor variants on the pins...
View ArticleProcedure to make incompatible parts changes to core parts?
Good to know, I think we only currently have the original (v 1.2) I'll dig up info an the W and make one of those too. I didn't know there was a pin change, I had assumed they were the same. Peter
View ArticleProcedure to make incompatible parts changes to core parts?
Not a pin change, just a couple of variants... don't remember what they are... There is also a built-in PCB antenna and solder pads for an antenna button. The breadboard layout is also a little...
View ArticleClik here to view.
Procedure to make incompatible parts changes to core parts?
While you are baking... don't forget about the Orange Pi's, Banana Pi's, and the Nano Pi's... O'yea, the Tinker Board too by ASUS...
View ArticleObter os Componentes
Bom dia. Sobre o sensor de corrente não invasivo eu não consegui encontrar o desenho correto para que eu colocasse no documento qque preciso. Com o termo que me falou na internet eu achei um mais não...
View ArticleCreating QFN-24 3.5mm x 3.5mm
Hi Guys, I have a serious problem. I had designed an entire PCB around a QFN-24 pin (3.5mm x 3.5mm) layout on fritzing. But only on ordering the PCB i came to realize that the fritzing supports only...
View ArticleCreating QFN-24 3.5mm x 3.5mm
You must be missing some letters because I can't see a 3.5mm QFN-24 What is the exact chip name, and where is the link to the datasheet.
View ArticleCreating QFN-24 3.5mm x 3.5mm
Given the data sheet / package foot print it isn't a big deal to modify a footprint and make a new part, but as Old_Grey said we would need a data sheet. Google finds references of a sort to qfn 3.5mm...
View ArticleObter os Componentes
Try this one: edit: replace with one with breadboard correctly defined ... sct-013.fzpz (7.6 KB) The pcb is a 3.5mm stereo jack as that is what the cable ends in. I think the pins are correct but of...
View ArticleClik here to view.
DB15 VGA Part Male and Female
Hi foks, I've been looking everywhere for a db15 vga connector part.at the end i've been puzzling to make it my self.so at the end after a 1.000.000 tries I got it. both male and female. I don't...
View ArticleClik here to view.
DB15 connector availability
I made it if you still need it DB15 VGA Part Male and Female parts submit Hi foks, I've been looking everywhere for a db15 vga connector part. at the end i've been puzzling to make it my self. so at...
View ArticleClik here to view.
125 kHz RFID module RF125-PS
I created the .fzpz file for another (other than the RDM6300) 125 kHz RFID module. bottom.jpg761x575 67 KB set.jpg783x542 54.8 KB top.jpg734x562 83.6 KB RF125-PS.fzpz (14.1 KB)I also wanted to add...
View Article