Parts position on the breadboard
its the board(ESPRESSIF ESP32 Wroom 32D) aswell as the ultrasonic sensor hc sr04.
View ArticleParts position on the breadboard
Yep the sr04 part in core is broken (misaligned by 0.05in in breadboard). As @opera_night suggested either turn of snap to grid by clicking View-Snap to grid, or a maybe better alternative use...
View ArticleClik here to view.
Parts position on the breadboard
HC-SR04.fzpz (30.4 KB) There it is. Thanks for fixing it
View ArticleClik here to view.
Sewable LCD Mounting Board (PCB)
OK, now… This, unless some additional problem crops up, will be the penultimate version. Sewable Display Mount PCB.fzz (11.5 KB) Sewable Display Mount PCB_pcb.jpg1026x459 228 KB Both of the top...
View ArticleParts position on the breadboard
OK here is a corrected version of one of the ones in core: HC-SR04 Ultrasonic Distance Sensor.fzpz (26.3 KB) Peter
View ArticleClik here to view.
Sewable LCD Mounting Board (PCB)
Something new (but undesireable!), when I try and download the latest fzz it says bad.PNG870x384 52.5 KB which I have never seen before. Maybe try uploading again? Peter
View ArticleClik here to view.
Sewable LCD Mounting Board (PCB)
Yep, uploading again. Sewable Display Mount PCB.fzz (11.5 KB)
View ArticleClik here to view.
Sewable LCD Mounting Board (PCB)
That worked, don’t know what happened with the first one. Looks good and would work as is, but I would increase your clearance in places because you have the room to do so. This is the copper bottom...
View ArticleClik here to view.
Sewable LCD Mounting Board (PCB)
Here’s where you get to throw a fit, because about 90%% of what you just did is now undone. I managed to get the distance needed for the R/A headers much more easily than I’d anticipated. Sewable...
View ArticleSewable LCD Mounting Board (PCB)
Not a problem, this is the normal course for laying out a pcb. Try something see if it works or doesn’t, then try and improve on it. Along the way some of the folks watching this may learn how to do...
View ArticleClik here to view.
STM32F303 STM32F103 RobotDyn BlackPill
While attempting to fix this on your own is a laudable goal, it likely isn’t too practical because parts creation is mostly undocumented (I’m trying to change that, but it is slow going.) The usual...
View ArticleSTM32F303 STM32F103 RobotDyn BlackPill
vanepps Thank you very much. I was impressed. As a result of the amateur’s hands, it has caused you trouble. I’m sorry. We will continue to use this site in the future.
View ArticleClik here to view.
STM32F303 STM32F103 RobotDyn BlackPill
bluefox: As a result of the amateur’s hands, it has caused you trouble. I’m sorry. Not trouble, as I said this how I learned to make parts from those who know more than I do. I’m just passing their...
View ArticleClik here to view.
Fritzing part L9110H motor driver
Hello Guys, does someone have a fritzing part for the L9110 motor driver or know where i can find one? Its this one: 3-L9110-Quick-Ref.jpg762x248 89.2 KB
View ArticleFritzing part L9110H motor driver
There is a dual channel driver module in parts-submit, but it doesn’t look like the chip is around anywhere. The easy way to make one is to copy in the generic IC from core parts in to your sketch and...
View ArticleFritzing part L9110H motor driver
With a generic IC loaded in to schematic (any view should do but schematic is probably easiest), click on the generic IC which will bring it up in Inspector (lower right window,) In Inspector click on...
View ArticleSewable LCD Mounting Board (PCB)
A late potential wrench in your plans. I was thinking about why you wanted RA headers, thinking that soldering in a standard low profile header would probably be as small or smaller, and realized you...
View Article