Clik here to view.
Export for Production (Etchable SVG) in CNC router
The Gcode generated by CopperCAM does not have the format (dialects?) compatible with the Gcode expected by controller of the GRBL (Arduino). Example Gcode generated in CopperCAM ... 2016-10-28...
View ArticleExport for Production (Etchable SVG) in CNC router
I expect you would do better asking in the CopperCAM forums than here. There is more of a chance that someone using CopperCAM would know about Arduino compatability and how it can be achieved (if it...
View ArticleClik here to view.
Export for Production (Etchable SVG) in CNC router
asasergio: Is there any solution for this? Yes, you would need to setup a Post-processor for the GRBL (Arduino); In CopperCam, in the menu, click on Parameters / Data Output Format, and then click on...
View ArticleMove Labels in PCB-view
Ahhh, that was it! I had changed the PCB to single-layer from double-layer, changing it back to double-layer solved it. I can now "manipulate" all the labels without using my "workaround". TNX Dan
View ArticleClik here to view.
Export for Production (Etchable SVG) in CNC router
steelgoose, You again demonstrated that there is a solution in CopperCAM and also provided me with some tips on how to achieve this. 2016-10-29 11_37_20.jpg1356x847 197 KB So I guess now I'll have to...
View ArticleExport for Production (Etchable SVG) in CNC router
It is not as difficult as it looks... Depending on how your router is set up; like, is your spindle turned on by the controller or manually... if you turn it on by hand then you don't need the M codes...
View ArticleClik here to view.
Dark circuit - Dunkelschaltung
Hi!I built a dark circuit - "Dunkelschaltung" which should light a LED on 9V when it is dark. I used a BC547 Transistor and some resistors. 1k on the Base and 1x 100k for sensitivity of the...
View ArticleClik here to view.
There is no FC-51 IR obstacle sensor?
How could it happen that I can not find the FC-51 IR obstacle sensor in the library? infraredobstacleavoidancesensormodulee96303d3800x800_1410349015.jpg700x700 50.9 KB
View ArticleDark circuit - Dunkelschaltung
If it works with 1 LED, maybe there isn't enough current to supply many LEDs. I'm not a electronics guy, so only guessing....
View ArticleClik here to view.
Need help with LED Push Button Solder Fan
HelloNew to the forum. New to the world of electronics. I'm trying get the electronics set up correctly for my fist project, a small fan to keep the solder fumes out of my face. I finally figured out...
View ArticleNeed help with LED Push Button Solder Fan
Your sketch doesn't appear to be correct although it probably explains the blown leds. The leds (assuming they are connected in parallel which sounds like the case if they run on 3v) want to see about...
View ArticleDark circuit - Dunkelschaltung
You are likely running out of gain and/or base drive on the transistor. Assuming r3 is the 100K resistor you aren't getting a lot of base current flowing. 9v / 100k = around 90 uamps of base current....
View ArticleProblems with lines in schematic view
Not sure whether to post this as bug yet. I can't be the only one having these problem, but maybe I am missing something. I was asked for a circuit diagram of my Mk I Arduino robot (stroppy tech...
View ArticleProblems with lines in schematic view
Are you are going File/as image,PDF, because mine in fine Sometime the sketch new redrawing. Close the sketch and reopen it.
View ArticlePart for new SBC
CHIP (or more precisely C.H.I.P.) is an unfortunately-named embedded single board computer with an ARM-based processor. It is comparable to a low-end Graperain and Raspberry Pi .
View ArticleExport for Production (Etchable SVG) in CNC router
There seems to be a preference for the use of the Eagle (to draw the schematic and PCB) and its PCBGCode plugin (to generate Gcode). Among some of the PCB design software that I rated, I realized that...
View ArticleExport for Production (Etchable SVG) in CNC router
I have small circuits that are easily drawn in Fritzing or other CAD PCB tool. I found tools that can import Gerber files (generated by Fritzing or not) and export G-Code, so theoretically it would be...
View ArticleClik here to view.
Problems with lines in schematic view
Tried that. If you turn off the 'helpful' smoothing preferences in adobe you can see it better, but they are there either way. It's in the FZZ file data too. Pasted image1280x760 44.2 KB
View ArticleDark circuit - Dunkelschaltung
Thank you.. I assumed that, but im not so experienced in building circuits.Can you send me a sketch of that circuit? yours Martin
View Article