How to Make Capacitive Touchpads in Fritzing
Thanks for suggesting the gerber viewers. I'm concerned because none of the holes are showing up, this includes the vias and the through hole components. Any ideas why this would be happening?Also,...
View ArticleHow to Make Capacitive Touchpads in Fritzing
The Fritzing pads are connectors... and all connectors do not has solder mask on them so you can solder to them. You would need to replace the Fritzing pads with your own custom pads. Are your holes...
View ArticleNew parts editor not available
You actually want to adjust the size of the viewbox in the xml rather than use resize page to content. The size of the viewbox affects the boards alignment on the grid in Fritzing and blindly using...
View ArticleChange the physical size of a sliding pot
You would need to use Inkscape or another svg editor to modify the breadboard svg file (which is more complex than this brief reply makes it sound).
View ArticleClik here to view.
Part Editor confusion
I'm often frustrated but rarely bored Also the though struck that schematic may be using the part number property in parts editor rather than the label property. If there isn't a part number property...
View ArticleChange the physical size of a sliding pot
No worries. Thanks again for your help vanepp. I was thinking that I could edit the part within fritzing. lll Google it more to learn what you described or I'm sure someone out there has one that they...
View ArticleClik here to view.
Change the physical size of a sliding pot
Have a look at these two for a start (both in here): A new part creation HowTo (long! So long it is in 2 posts) beginners (Edit: November 2016: This is an updated (and corrected) version of the...
View ArticleHow to Make Capacitive Touchpads in Fritzing
Ok, thanks, I'll replace the pads with the same technique of inserting an svg image as a logo object and putting into the copper layer. Will these still be the same thickness and work as well with...
View ArticleHow to Make Capacitive Touchpads in Fritzing
Copper is copper... If it is a 1 mil copper board then all copper on the board will be 1 mill thick. Gerber viewers are weird, they all work a little different. Try looking at the board in Fritzing...
View ArticleCreate snap point part
How to create a snap point in a part with illustrator.Must a add a special layer with specific name? In which view a must added? breadboard or pcb? Many thanks vfor any help
View ArticleCreate snap point part
Is a snap point the same as bendable legs (i.e. the wires in breadboard view on some parts) or something else that I don't know of? I know how to make bendable legs but not a snap point (nor what that...
View ArticleSearching parts, Velleman RX 433Mhz and SMA Connector
Hi, I'm wondering if the following parts exist:...
View ArticleCreate snap point part
Thanks for your respons. What i mean is the following.When you place a part in the breadboard view it's snap automaticly to the grid.Now a have craete a magnet that have no bend legs needed because...
View ArticleMKR1000 fritzing part
MANY Thanks for the fix on the MKR1000, Steelgoose . . . I needed that too.
View ArticleCreate snap point part
Ah, while I'm not sure exactly how to do that (with luck someone else will), I believe Fritzing is snapping to connectors. So you could (and may have to) put in a fake connector for it to snap to.
View ArticleClik here to view.
Searching parts, Velleman RX 433Mhz and SMA Connector
Try the RXB6_Superhetrodyne_receiver.fzpz from this post. The Sparkfun part is wrong (one pin too short) so I corrected it for this person with a similar board. Diode ( keine Led ) Bauform 0805...
View ArticleNodemcu part for fritzing
Hi, forgive me for my bad english. I'm looking for the part of nodemcu 0.9 devkit which seems to be larger than the 1.0. I can't find this version over the net ?
View ArticleCreate snap point part
So you have a part without contacts, and actual magnet, and you want it to snap to the grid. We will have to see what Steel says, but I don't think you can do that. If you make a fake contact with...
View ArticlePart Editor confusion
After much delay I'm back with the file you offered to look at. Thanks.INA125.fzpz (6.0 KB)
View ArticlePine-A64, ESP8266-12E/F, Arduino ZERO, and MKR1000 - New Fritzing Parts
Hi. I'm making an open source app and I would like to use the Arduino Zero svg file on it. I want to know if I can reference this file for that. Thanks.
View Article