Part Editor confusion
OK, I'm unclear that this is correct, because google says an INA125 is a 16 pin instrumentation op amp not a mircrocontroller, but here is a part with the part numbers corrected. I unzipped the fzpz...
View ArticleArduino Mega 2560 (Rev3) std with silkscreen
The std under mounted Arduino Mega 2560 (Rev3) with component silkscreen and text added to PCB view. The USB, and maybe the power connector, will hit any PCB component pin that is mounted directly...
View ArticleClik here to view.
Wemos D1 mini PCB protective areas rotated
Hello, I'm Mike, the original author of the part.I've fixed the rotated pcb issues in my latest version (v3). github.com/mcauser/Fritzing-Part-WeMos-D1-Mini Issue: All pins are on one horizontal row...
View ArticlePart Editor confusion
Well just crap. I'm really sorry to put you through all of that but I'm using a INA126. An 8 pin amp. I am using an Arduino and a load cell in project and the 126 is my amp for the load cell. Thanks...
View ArticleClik here to view.
IoT Shield for Arduino
Hello, I'm writing to let you know about 'ARMA IoT: Breakout Board for ARDUINO'. It is an IoT shield for Arduino. The board is compatible with Blynk, thingspeak libraries and it is very cool for...
View Article0.9.3b unusable on 1080p display with 1.25x scaling
I'm running Fritzing on a Panasonic Touchpad tablet, FZ-G1, under Linux 64 bit. All was working fine, but I've done something and the resolution when I start up Frizting is way larger than the screen....
View ArticleCreate snap point part
How is Steel? No problem with a drilled hole.So i understand that i must create in the PCB SVG view a copper layer and make the drilled hole? I must also create on the same place as in the PCB view a...
View ArticleClik here to view.
Pine-A64, ESP8266-12E/F, Arduino ZERO, and MKR1000 - New Fritzing Parts
Sure, you can do anything you want with it...
View ArticleCreate snap point part
You would need to add a connector to the part (in all layers) preferably aligned to the grid. You may be best to start from a part with a single pin in it (such as a 1 pin connector) as that will have...
View ArticleClik here to view.
Part Editor confusion
Not a problem, I've been in parts creation hell for months and am just paying forward all the help I've gotten. Even better than the generic IC would be to start with one of the op amp ICs which have...
View ArticleClik here to view.
Motor control over internet
Hello, I would like if possible to control 1 motor with a wemos d1 over internet or lan, mention that the engine is connected to the L298, I need to control direction and speed. i am a novice, please...
View ArticleAuto-relocating of part placement problems
Hi, unfortunately i'm facing an error which totally breaks usability for me. When inserting a via1-part into the pcb sketch and trying to set up his placement whenever i filled one of the location...
View ArticleAuto-relocating of part placement problems
Assuming you are trying to do this from the parts editor, you may be able to work around it by saving the part and then using Inkscape or another svg editor to move the vias to where you want them in...
View ArticleAuto-relocating of part placement problems
Well, that workaround is not looking far enough. If there is a problem with placing elements precisely i could of course try to build the component completely in inkscape or whatever, but when i'm...
View ArticlePart Editor confusion
I was one digit off. 'I always mess up some mundane detail'. Classic Office Space movie quote. I agree that is a better idea using an existing amp. Thanks again for all you help and work.
View ArticlePart Editor confusion
No problem, feel free to ask for help going forward, parts creation is poorly documented and complex but there is a fair amount of experience around.
View ArticleAuto-relocating of part placement problems
If you need zero tolerance, something that you don't see in machining, you should not be using FZ, or probably not any free EDA. 9 micron way good enough for beginners, which is what it was designed...
View ArticleAuto-relocating of part placement problems
Sure, i see. It obviously is a feature. Was i blind!I can always use something else, but i was hoping that somebody would care about bugs in their beloved software. If you ever actually tried to place...
View ArticleAuto-relocating of part placement problems
Yeah I know. I put a request for bigger X,Y coord box and a ruler as a patch, but that was a while ago. In actual fact if you could position stuff perfectly in the drawing, that actual machining...
View ArticleFull bridge load cell
If anyone has some free time, I would like to request a simple load cell added to the parts bin. Like this one. I cant find one on the net. https://www.sparkfun.com/products/13329
View Article