Looking to pay someone to create a large part
Sorry for the late reply @vanepp, The LED section of the push buttons are on the right hand side, while the switch contact section of the push buttons are on the left hand side.
View ArticleClik here to view.
Looking to pay someone to create a large part
Just downloaded your work and it looks fantastic, well done and I can't express enough my appreciation for your work. It's just fantastic, even just playing around with the LCD connections and the...
View ArticleClik here to view.
Looking to pay someone to create a large part
Hi @Dee_Faux, I know how you feel, i've been busy with a number of electronic projects lately also There is no rush on the website and appreciate your offer of help on the site - in fact, I've been...
View ArticleClik here to view.
Looking to pay someone to create a large part
Hey Brad, Thanks for the reply. Like the word "No Rush" . Yes, that is a good start and sure you'll enjoy the learning experience. In fact, I wasn't ready to hard code the website from the ground up...
View ArticleIs it possible perhaps a Daft question
Hi all/vanepp, I am about 90% through putting the breadboard together, 1st problem is the LEDs, should the centre pin go to ground not positive as in the circuit (the LEDs I am using are bi/colour...
View ArticleLooking to pay someone to create a large part
Hi Brad, If you could send Peter this drawing in a Postscript or SVG it could save Peter a lot of work. You can zip it up with the extension .fz.
View ArticleBlank RPi HAT PCB
@Tenderfoot14, I almost forgot... actually, I did forget... I got sidetracked. Too many irons in the fire... Here is your Pi Zero PCB Shape (Hat). I had started to use the Pi Zero in Fz as a pattern,...
View ArticleClik here to view.
LED Flicker tester
This is probably a better bet although I'd probably replace the 3.3 regulator with a cheap ($2 - $3 from ebay) buck regulator such as this (the first one I found in a search for buck regulator on...
View ArticleClik here to view.
Looking to pay someone to create a large part
Nah the jpeg above is fine. I already know most of the pins and that drawing clears up the few I didn't know. Now all I've got to do is edit in proper pin numbers in to the breadboard and merge the...
View ArticleClik here to view.
Is it possible perhaps a Daft question
There are two led types common anode (which I used) and common cathode (which may be what you have).If your leds are common cathode then yes the drawing needs to be the reverse the led common to...
View ArticleClik here to view.
Looking to pay someone to create a large part
Some electrical (not Fritzing related ) thoughts on this, which if the boards are done may be too late. I don't see current limiting resistors on the various led leads. While values may be difficult...
View ArticleClik here to view.
Looking to pay someone to create a large part
Good point @vanepp, I put all of the 'driving' circuitry on the underside of the PCB such as the 555 timer, current limiting and pull down resistors, transistors for the seven segment display and...
View ArticleClik here to view.
Looking to pay someone to create a large part
Good, you had already thought of that . I think I'll leave them out of schematic view as well to not add confusion there either.
View ArticleClik here to view.
Looking to pay someone to create a large part
Are the rgb leds common cathode or common anode? Since the one in Fritz is common cathode I'll assume that for the moment and change it if necessary. Same for the leds in the pushbuttons common...
View ArticleSVG import not correct sizing
Okay, so... here's the export of my erroneous part. There's also a link to the datasheet in the description. Thank you so much for the guidance! I'm sure it's something simple that I'm missing....
View ArticleLooking to pay someone to create a large part
The RGB LED's are common Cathode and the push buttons are also.
View ArticleSVG import not correct sizing
I'm guessing it's something in the internal XML coding of the PCB svg, but I'm not smart enough to work that out. I drew another rough one from scratch that's not dimensionally accurate and works...
View ArticleGerber Files and dirtypcbs.com
I have no problem with Seeed Studio Fusion for pcb prototype. They also require gerber file. Maybe you can have a try.
View ArticleAlmost totally new to electronics and I'm trying to prototype a device in...
I want to give my oil filled radiator a bit of intelligence. Right now I have it plugged into a super old-school timer which fulfills my needs fairly well, but I'm interested in learning about...
View Article