Clik here to view.
Barn-door Astrotracker
vanepp: First the Gnd pin on the bottom right needs to connect to ground on the Arduino (there are two grounds on the motor driver, one for the motor which is connected correctly and one for the logic...
View ArticleHow to sense sound from an insect using Arduino
Hi alli'm doing a project based on sound recognition in matlab , i need to import the same (Matlab code) into Arduino .Kindly suggest the hardwares and technique to complete this project
View ArticleClik here to view.
I can't install the FRITZING Software in my system
i can't install the FRITZING Software in my system (Windows 7 32-bit operating system)
View ArticleBarn-door Astrotracker
What are those 2 black forked wires with the red ends under the step? It doesn't matter for BB view but if you PCB it always look for red ends, as it denotes a non connection. EDITAlso those 3...
View ArticleI can't install the FRITZING Software in my system
You haven't installed the MS crt runtime. Plenty of fixes posted around here.
View ArticleFirst part for review
If I understand your question correctly... Just add the pads back into the pcb.svg. Try this one... is this what you want? PM6078-004_v2.fzpz (6.6 KB)
View ArticleClik here to view.
Barn-door Astrotracker
This multiple views thing will take some getting used to (I'm new to fritzing and haven't used it a lot yet), I was looking at the schematic view (which as you note was incorrect) and didn't think to...
View ArticleSearch function in the parts view does not work
Odd as I have a couple of machines running Win7 pro 64 and fritzing 0.9.3 and the search runs fine on both. As you note on start up it is greyed out, but clicking on the search arrow causes a brief...
View ArticleClik here to view.
First part for review
Yes! Thank you, that looks to be what I want, now all I have to do is figure out how you did it . Parts editor doesn't seem to be complaining about unconnected pins and the appropriate pads have re...
View ArticleFirst part for review
I just replaced my pcb.svg file with the one from your part and all is well, the new pads show up and the fonts are the correct size. So now all I need to do is go look at the xml and see if I can...
View ArticleClik here to view.
First part for review
I was going to explain how to fix your pads but it was a lot easier just to fix them. It is really pretty straight forward... I will write up something for you so you know how it works... I saw this...
View ArticleFirst part for review
Thanks, a write up would be appreciated, but it looks pretty easy. I've got the two files up in Inkscape and (other than the fact Inkscape has lost the left side and top lines on your file, fritzing...
View ArticleClik here to view.
First part for review
Yep, that is it, just add a bunch of circles... I do it all in CorelDraw with the duplicate button... only takes a few seconds. Wired, I didn't touch the breadboard or schematic .svg's, but when I...
View ArticleFirst part for review
I am going to try that in Inkscape and see if it will duplicate only the pad without also copying the terminal pins. At the very worst I can use XML editor to delete only the pin parts I expect and...
View ArticleClik here to view.
First part for review
We having fun yet!!! The schematic.svg appears to be a raw inkscape .svg, When I exported the part. FZ rewrote it into FZ format. The inkscape fonts were sized in pixels instead of points. There are...
View ArticleFirst part for review
I actually click on the node in Ink's XML Editor to select it, like the circle, then go to the drawing and right-click the boxed node - must be arrow select - and select duplicate. That way you know...
View ArticleClik here to view.
First part for review
Yep that one works fine. Knowing what the issue is helps a lot too. It looks like font size in pixels is a feature in Inkscape (i.e. the manual shows no way to change it to points, only how to resize...
View ArticleFirst part for review
I'm not good at direct XML coding of the .fzp file, I meant the XML Editor in Inkscape. It's simple shuffling stuff, adding nodes, renaming, etc. In Ink File/Properties you can set global pt, maybe do...
View ArticleResistor sizes [extra text required for the title]
i guess this is beginner, so. i have a perfboard placed out and I'm trying to do 2 things. extend the legs on a resistor place a component the wrong way on a board. i select a resistor from the core,...
View Article