Schematic to breadboard layout
I mentioned it on the arduino forum, this is what a couple of people said "You need the same amount of { as }. The brackets around toggle=1 are probably wrong. Try to autoformat the source to make it...
View ArticleClik here to view.
Drill size does not match the copper hole size
I am fairly new to Fritzing but have successfully made custom Board SVG's and two custom parts but all of a sudden my latest part is having issues and after two days of variations and googling I can...
View ArticleDrill size does not match the copper hole size
Hole sizes are in the svg so you need to upload the ,fzpz file, or the complete sketch .fzz. Just use the 7th button above.
View ArticleDrill size does not match the copper hole size
Opps I thought that is what I had uploaded. Here is the correct one I think.IN-16 Nixie Tube.fzpz (13.3 KB)
View ArticleDrill size does not match the copper hole size
Yeah drill.txt shows 0.007" holes. Peter had that problem so he probably knows the fix - maybe because they are paths not circles -, but I would redraw a "circle" connector using the circle button,...
View ArticleDrill size does not match the copper hole size
Thank you for letting me know I do not need to duplicate all the paths from copper0 in copper1. When I created the SVG I only had three main groups. copper1, silkscreen. I then had copper0 group...
View ArticleDrill size does not match the copper hole size
Yeah FZ adds stuff. If you look at your export part everything is now 7 groups deep.
View ArticleDrill size does not match the copper hole size
Ok I remade the rings using the circle tool and it works now. Thanks so much. It exports perfect Gerbers now so I'm not too concerned. Is there a way to replace a part in a sketch without deleting it...
View ArticleDrill size does not match the copper hole size
Turns out that once I connect the pads to their respective nets the connection points move really far away. So I still don't have a working part.
View ArticleDrill size does not match the copper hole size
So I think I have it figured out. I removed all the extra groups, saved the svg over the last updated fritzing svg. Opened the part in the editor and reassigned the the pins and now it works. Here is...
View ArticleProblem with PCB created with Fritzing
I am creating a new part, bread board working, connections set, schematic ok, but when I try to load image for PCB, I load it, no error, but the graphic on screen is blank, I never get image. So I...
View ArticleDrill size does not match the copper hole size
13 holes 0.031", seams to be fine. We use Gerbv to view the gerbers, and add 1 layer at a time to check what each does. You can also add the drill file the same way to see the holes. You can draw the...
View ArticleProblem with PCB created with Fritzing
So this is the PCB svg for a part. It's hard to work out what going on without the svg, can you upload. Use the 7th button above for the part(better), or for the svg change the extension to .fzpz and...
View ArticleDrill size does not match the copper hole size
Thanks again. I also use Gerbview but I used Aisler's renders for my picture upload because they are pretty. The Schematic just isn't on my list of important things. I did check and you can find...
View ArticleSchematic to breadboard layout
The problem with the code you posted is that it isn't a program, it is a series of unconnected fragments of C. Even if I could make it compile (which is doubtful) it wouldn't do anything useful. The...
View ArticleDrill size does not match the copper hole size
.031 may be a little small (that is the standard size hole for an IC leg) from what I remember of nixie tubes (I haven't seen one in 15 or 20 years) the pins are more likely to be around .1 post size...
View ArticleDrill size does not match the copper hole size
Thanks for the reply. The legs are only 0.6mm or less on very small tubes that fit in a watch ( I have three different kinds). The hole size was chosen to fit the legs while still having room between...
View ArticleDrill size does not match the copper hole size
I just remeasured and the smallest tubes have 0.4mm leads so I shouldn't have any problems.
View ArticleDrill size does not match the copper hole size
I like Gerbv more than Gerbview because it has a ruler to check distances. You could put a oblong or rectangle on the pads and angle them towards the center if you need more mechanical grip to the...
View ArticleProblems joing wires or even attaching components to wires in breadboard design
I want to help you with better user experience.
View Article