Clik here to view.
Creating QFN-24 3.5mm x 3.5mm
Thank you old grey. I used the part that vanepp sent me. And i think its look good for now. I will send it out for fabrication. Fingers crossed that the chip will solder well onto the board. Thank you...
View ArticleCreating QFN-24 3.5mm x 3.5mm
You have to reset the grid and straighten the traces. Be 100% sure that it's right, as there is no use doing it wrong, by checking the Gerbers. There are online Gerber viewers, or you can use the free...
View ArticleCreating QFN-24 3.5mm x 3.5mm
Thank you Old_Grey. This time i printed out the circuit onto a PDF just to see if it somehow aligns to the chip i have. It seems to be more or less accurate :).
View ArticleClik here to view.
Creating QFN-24 3.5mm x 3.5mm
If you are going to hand solder this, then I'm glad I was lazy and left the pad width at its current .22mm instead of the .3mm recommended in the Infineon part. While it will make placement a bit more...
View ArticleCreating QFN-24 3.5mm x 3.5mm
I'm not sure if Van's 0.2mm extension to the pad is enough, but if the pad protrudes past the body of the part you might be able use a soldering iron and wick the solder under the chip. Then just put...
View ArticleITDB02 TFT Arduino Mega Shield v2.0 and mirrored Arduino mega
I created the ITDB02 TFT Arduino Mega Shieldv2.0 Use this part if you want to mount it on pcb instead of your arduino. I also edit the arduino mega with a mirrored pcb layout, this way you can mount...
View ArticleClik here to view.
Creating QFN-24 3.5mm x 3.5mm
Hi Vanepp, Thanks again for the advice. I can use both methods to solder. Personally i was about to use the solder paste + heat gun method as that worked for me before with the breakout board. And for...
View ArticleIBT-2 Motor Driver 43A H-Bridge Drive
Can I get a picture of IBT-2 Motor Driver 43A H-Bridge Drive
View ArticleClik here to view.
Creating QFN-24 3.5mm x 3.5mm
They aren't that far off, its just that all the distances are small and every little bit helps . Hope this works for you. Peter
View ArticleIBT-2 Motor Driver 43A H-Bridge Drive
Assuming that you are looking for a fritzing part (rather than a picture) for the motor driver, the answer is that there seems to be one (the third or forth article here has a picture of it) but I...
View ArticleIBT-2 Motor Driver 43A H-Bridge Drive
fritzing part IBT-2 that’s what I’m looking for.Any help out there?Thank you
View ArticleIBT-2 Motor Driver 43A H-Bridge Drive
Your best bet would probably be to try and contact the person that did the blog post. He obviously has a fritzing part for the driver and may be willing to share it. Otherwise you would need to create...
View ArticleClik here to view.
IBT-2 Motor Driver 43A H-Bridge Drive
There seems to be another one. instructables.com 4WD All Terrain Arduino Robot for Everyone : 6 Steps I've always liked robots that can move in rough terrain. This time I decided that I will use...
View ArticleIBT-2 Motor Driver 43A H-Bridge Drive
Again a picture of the fritzing part but no part source to be found. However someone else to ask if the part is available ... edit: If you manage to find a part, please post it or a reference to it...
View ArticleClik here to view.
DB15 VGA Part Male and Female
Welcome to parts creation hell , sounds like you have already been bitten by the monsters but prevailed, hope you continue creating parts. That said there are some problems (none terribly serious): 1)...
View ArticleClik here to view.
IBT-2 Motor Driver 43A H-Bridge Drive
I tend to skip over the question because I'm lazy, but now looking at it he might want a good top pic to make the BB view. You can do a Goo Image search, but remember adding 1 word can get different...
View ArticleClik here to view.
Creating QFN-24 3.5mm x 3.5mm
Will let you know Peter. You just saved my ass . I had no idea how to create parts and do graphics. If i had to move to Eagle or Altium which had this part. It would take me weeks just to know the...
View ArticleClik here to view.
Creating QFN-24 3.5mm x 3.5mm
For me (after struggling with parts creation for coming up on a year with lots of help from the other folks in here ), only an hour or so with Inkscape and the data sheet. To someone new to parts...
View ArticleFritzing is crashing during Gerber export
I am having a problem where Fritzing just crashes and hangs when I choose to do a gerber export. When I look in the export folder it has only got as far as the pnp.txt file. Does anyone have any idea...
View ArticleFritzing is crashing during Gerber export
Have you waited an unbelievably long time? I know for me on Linux with complex Fritzing sketches it causes the program unresponsive message and asks if I want to force it quit all the time and not...
View Article