Clik here to view.
Hi Ya'll, noob here :)
Thanks for the quick answer, indeed that’s not what I had in mind So I must keep in mind to copy the used HTML files into the experimenting map so I don’t loose them (as I am always loosing stuff when...
View ArticleClik here to view.
Hi Ya'll, noob here :)
estate: So I must keep in mind to copy the used HTML files into the experimenting map so I don’t loose them (as I am always loosing stuff when I am busy and think about nothing else than what I am...
View ArticleClik here to view.
LinkIt One Development Board
Thanks! Well based on Old_Grey original .svg file, I let the same pin names because that is the last thing to do after finishing a piece. Now I will take a look at the pinout diagram and assign the...
View ArticleHow to create Circular Pads?
Hi, How to create a circular pad in fritzing ? I searched for it but couldn’t find it. Thanks
View ArticleClik here to view.
LinkIt One Development Board
KingDarBoja: Page properties tab: Grid units: px x, y origin: (0, 0) x, y spacing: (1, 1) Primary line each: 5 For this one I use x, y spacing: (.01,.01) Primary line each: 10 which when zoomed way in...
View ArticleClik here to view.
Hi Ya'll, noob here :)
Hhahaha Peter, Old, tell me I should have discovered Arduino years ago at 65 you do not learn as fast so Git is a bit too much for me too
View ArticleHow to create Circular Pads?
Grab a via out of the Core bin and adjust the size in Inspector.
View ArticleLinkIt One Development Board
Finished part: linkit_one_board.fzbz (89.8 KB) But I really can’t get it to fit perfectly the .1 grid thing, not sure why, I always check it on Inkscape but on Fritzing, it has a little offset thing...
View ArticleClik here to view.
Request - IRF520 MosFET module
Final fix: IRF520_mos_module.fzbz (23.3 KB) It should be perfect right now
View ArticleClik here to view.
Hi Ya'll, noob here :)
estate: I should have discovered Arduino years ago at 65 you do not learn as fast so Git is a bit too much for me too I’m 68, retired and enjoying my second childhood doing what I want, which is at...
View ArticleProblem in running second time after installation in debian stretch
How can a git repository for multiple architectures have a binary that works for mine ? I can understand how that might be true of the architecture specific downloads
View ArticleClik here to view.
Problem in running second time after installation in debian stretch
dhlii: How can a git repository for multiple architectures have a binary that works for mine ? It doesn’t. The binary is from the download you get at Fritzing,org which is the one you linked to in...
View ArticleLinkIt One Development Board
I think the grid starts at the edge of the page size so you make it a touch bigger until it lines up. You usually ‘select all’ and ‘resize page to selection’, but in doc properties you can adjust the...
View ArticleClik here to view.
Problem in running second time after installation in debian stretch
Specifically this post which builds head for me on Ubuntu 16.04lts linux and Windows7pro (although I think windows can be simplified somewhat, this works for me). Build instructions for Linux and...
View ArticleHow to create Circular Pads?
But what about removing the hole ? I cannot set the hole diameter to 0, it won’t accept a 0 value.
View ArticleFritzing part for QF 40 pins
Here is the link http://pdf1.alldatasheet.com/datasheet-pdf/view/865305/EXAR/XR10910.html
View ArticleClik here to view.
LinkIt One Development Board
Old_Grey: EDIT Holly cr@p, that’s nice. Yah, that was my reaction too . Now on to the faults. Breadboard alignment is fairly easy. The connectors are different sizes connector0pin is w 0.056 h 0.056...
View ArticleHow to create Circular Pads?
Well then I think you need a part. I think I remember a post recently where someone made the via hole half the thickness of the ring, or something like that, and that removed the hole.
View ArticleLinkIt One Development Board
Pin connectors are straight off the UNO, and we know most parts aren’t prefect, but then again it’s not supposed to fit on a 0.100" breadboard, like an UNO, so maybe it will do as is.
View ArticleFritzing part for QF 40 pins
I think this footprint should do you. As always before ordering boards check the footprint against a real part. This is a generic 40 pin IC with the qfn40 footprint in pcb. You would need to add a...
View Article