Fritzing part for QF 40 pins
Thanks a ton! Did you just create it ? How did you make the part so quickly ?
View ArticleWhere to hire someone who can make a full service
Hi Where should I start if I want to hire someone to make a full project ready to one click fabrication with all the needed files and electronic calculations. from an idea to a finish and ready to use...
View ArticleSearching for ST7735B - 128x160 TFT LCD Display part
Thank you for making the part. I was looking for a copy of whatever had already been made. if you need accurate mounting holes you would need to measure a real board and adjust the part to match Yes,...
View ArticleArduino Mega 2560 Shield v2.0
Hi mate, nice to hear that, the arduino mega shield v2.4 you designed was pretty good indeed. I tried to use it for the v2.0 one since it has similarities regarding header layout but I switched to...
View ArticleFritzing part for QF 40 pins
Once you get past the learning curve of making parts, it is reasonably easy to make parts. In this case I started from a generic 40pin dip, changed the metadata in parts editor then exported the part....
View ArticleClik here to view.
Searching for ST7735B - 128x160 TFT LCD Display part
MMushovic: Yes, the pins should align with a standard breadboard. I’m not sure how to fix this. The header pins are fine. They are standard .1 spacing and will fit breadboard just fine. They may not...
View ArticleWhere to hire someone who can make a full service
This is likely to be quite expensive to do in this manner (and Fritzing may not be the appropriate tool to do it). I guess wait and see if anyone offers a price, or perhaps someone has a reference to...
View ArticleClik here to view.
How to create Circular Pads?
Use the “Hole” part. Image of example’s of a ‘Hole only’ and a ‘Hole with Pad’. You can set hole diam and ring thickness (0 thickness means no pad/hole.Thus, for Pad only, use 0 hole diam). Screen...
View ArticleWhere to hire someone who can make a full service
Thanks for your reply, Peter… Can that be correct maybe I explained it wrong. A project like this setup in fritzing. http://fritzing.org/projects/lauflicht-mit-poti That could not be that much maybe -...
View ArticleClik here to view.
Where to hire someone who can make a full service
jokerper: Where should I start if I want to hire someone to make a full project ready to one click fabrication with all the needed files and electronic calculations. From this I took you to mean that...
View ArticleHow to create Circular Pads?
The problem with both ideas is you will get a pad on both sides of the board and if you want a round pad I’m sure it is for some SMD application where you want it only on one side. If it were me I...
View ArticleHow to create Circular Pads?
Gee, I didn’t know holes have rings. I suppose you can make 2 sets of gerbers one with circles and one without, and then just swap the without for the bottom layer.
View ArticleHow to create Circular Pads?
Quite true. However ConMan didn’t provide info re board/layers… Most often I CNC machine my boards and blow away un-needed pads and holes in CopperCam. Naturally, if laboring making boards via the...
View ArticleSelect PTC fuse
By dumb luck the PTCs I ordered on Ebay were PPTC, if the description is correct. I video-ed the surge. The 1st Speedy(Arduino EFI) is the one with the blown traces, but I also test my other Speedy at...
View ArticleSearching for ST7735B - 128x160 TFT LCD Display part
I guess I still have a few things to learn about using Fritzing interface. I just reloaded this part and it lined up perfectly with the breadboard parts. Thank you again for making this. I’ll try to...
View ArticleSearching for ST7735B - 128x160 TFT LCD Display part
Ah, you were likely bitten by one of the bugs in Fritzing. It sometimes doesn’t align parts on the grid until you move them and then they snap to the grid correctly. Another is if you drag the part in...
View ArticleClik here to view.
LinkIt One Development Board
vanepp: Breadboard alignment is fairly easy. The connectors are different sizes connector0pin is w 0.056 h 0.056 connector46 and 47 (and the grove connectors) are w 0.020 h 0.019. I had to google...
View ArticleLinkIt One Development Board
If you node select - under arrow select - in INK and click on an object in the drawing it will highlight in the XML dialogue. This part can’t connect to a breadboard in real life so it doesn’t have to...
View ArticleClik here to view.
LinkIt One Development Board
We should do a new topic about standard measures when making a part in fritzing This topic should include all information regarding how to setup grid, units and so on inside Inkscape (or illustrator)....
View ArticleClik here to view.
LinkIt One Development Board
KingDarBoja: Basically Fritzing doesn’t place the drawning wires at the connector middle point (x,y) but instead to one of the corner (Bottom left). I had no idea about it Not quite. It is a...
View Article