LinkIt One Development Board
We actually had this conversation before. Some people wanted to make everything BB connectable, but I had the impression that FZ creators wanted BB view to be real world so very young children can get...
View ArticleClik here to view.
LinkIt One Development Board
vanepp: connector1 is wrong (no terminal id which makes the line connect to the center of the pin rather than the end in schematic) It probably is a program bug since every pin has his own terminal as...
View ArticleClik here to view.
LinkIt One Development Board
Looks good, although one (hopefully last ) minor issue. In schematic the font size on vin is too small, it is tiny compared to the letters next to it. At first I thought you had been caught by an...
View ArticleClik here to view.
LinkIt One Development Board
Last fix done LinkIt ONE board.fzpz (89.0 KB) Thanks for the help vanepp. Now I shall move to the real hardest part I should finish right now: Arduino mega shield v2.0 But first, gonna start spanish...
View ArticleLinkIt One Development Board
MAKE SURE YOU CHECK THE PCB FOOTPRINT BEFORE GETTING PCBs MADE BECAUSE IT WAS MADE WITHOUT A DATASHEET AND GUESSED THAT IT IS AN EXTENDED UNO FOOTPRINT. I’ll just add this here again because I don’t...
View ArticleDo I need ground fill and if so how do I do it?
Hi guys. I’m working on a double layer tht PCB and I have some concernes about my ground. I have place ground fill and it seems that all GND pins are connected with the plate but Fritzing still shows...
View ArticleClik here to view.
How to invert a PCB icon
Hi I am new here, I am trying to do the PCB layout shown below. The view is from above but the copper tracks are from below. The problem is that the way the 555 timer is in the layout is as if it is...
View ArticleHow to create Circular Pads?
Thanks a lot guys. Swapping the gerbers seems a decent method. I think I am gonna try that out.
View ArticleHow to create Circular Pads?
Just found out that you cannot make a connection with a hole.
View ArticleTEA5767 SMD Module
It is my first part that I created using inkscape, so don’t expect a lot!. Also if you find some errors please report me.TEA5767 module SMD.fzpz (6.3 KB)
View ArticleWhere to hire someone who can make a full service
I don’t know what the project is but I might make it for you, if you can make it clear what you really want.
View ArticleDo I need ground fill and if so how do I do it?
Copper fill fills areas without connecting to anything, and ground fill connects grounds. If you ground fill it shows the grounds connected with ratsnests - black dotted line -. You can also double...
View ArticleWhere to hire someone who can make a full service
I think for a start price. So I know how much we are dealling with. 1 BLUETOOTH CHIP 4.0 prepared for use with the Arduino IDE interface. 1 BT antenne 1 AUDIO STEREO HIGH GRADE OUTPUT min. 2x25watt...
View ArticleHow to invert a PCB icon
On the bottom red bar you can select view, and whether it’s showing a side or both. By the look of it it is showing the bottom and through the PCB to the top.
View ArticleHow to invert a PCB icon
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
View ArticleHow to invert a PCB icon
Sorry I see whats wrong. You must have selected bottom layer and pulled parts on, and that mounts them to the bottom. Select view from above and both layers and then I think you select the part and...
View ArticleHow to create Circular Pads?
Will square ones do, because you can select Pad. Other than that it’s a via with a hole or a custom part.
View ArticleHow to invert a PCB icon
But wouldn’t that place the copper pads of the 555 on top of the PCB? I want a single sided PCB since I am going to be using a copper clad board.
View Article