How to créate a streapboard the same like in the picture?
Thank you for your answer Peter, I found how to modify, cut or add tracks Tomorow i will post a screenshot of my work. (For me , the links of vidéo are also broken) Please, another question: I think...
View ArticleClik here to view.
How to créate a streapboard the same like in the picture?
gemini07: I think it’s the printed circuit board that we see, so how to display the streapboard components side in Fritzing ? Unfortunately you can’t in breadboard. To view both sides you need to do...
View ArticleSmall Transformer 14x19x15h
It seams to be latching. I’m using a wire as a switch and when I close it the LED goes on, but when I open it it stays on. EDIT After playing for a while the 555 caught fire, so I tried another and it...
View ArticleSmall Transformer 14x19x15h
For testing you may want to try something like a 10uf cap as C3 (plus towards pin 6/7) and 47K as R2 to give you a long time constant (around .5 sec) of output pulse. Then a tap on the trigger should...
View ArticleClik here to view.
How to créate a streapboard the same like in the picture?
I think I understand … I made a screenshot of this video: Here the “A” part is the botom (printed circuit board side) and the “B” part, the top (component side) allright?
View ArticleHum-900-prc part
I think this part should work for the -ufl or -cas versions of the part (but I think only the -ufl version will work with Fritzing) as the footprints are the same. Schematic and labels are for the...
View ArticleClik here to view.
How to créate a streapboard the same like in the picture?
gemini07: Here the “A” part is the botom (printed circuit board side) and the “B” part, the top (component side) allright? Yes that looks to be correct in this case (although this strip board looks to...
View ArticleClik here to view.
How to créate a streapboard the same like in the picture?
Thank you for your explanation ! I wanted to be sure that when I put a component on the streapboard with Fritzing, it would be the same in reality with my plate. (That it would be well disposed)...
View ArticleHow to créate a streapboard the same like in the picture?
I’ve made some parts which are available here in the forums (I’ve been so far too lazy to submit them on github to get in to core parts) of parts that are shrunk for perf board use as have other...
View ArticleDoes an Arduino Uno Mega Shield SD Card ICSP SPI Exists Already?
Hi, Very new to Fritzing, it is awesome! Thank you. I have a test shield for the Uno that has a built-in SD card. My project has exceeded the capacity of an Uno and was looking to use a Mega 2560....
View ArticleSmall Transformer 14x19x15h
I got some new TI 555s and had to use 100uf for C3, but only the first press has a delay. You press it the 1st time and it stays on for 3 sec, but any press after that and it’s instantaneous again....
View ArticleHow to créate a streapboard the same like in the picture?
That original pic is of a very old version of Fritzing, and the darker greenish tracks “A” are indicating it’s connected to the IC. Not top/bottom. AFAIK all stripnoards are single-sided on the bottom...
View ArticleClik here to view.
Small Transformer 14x19x15h
Old_Grey: I got some new TI 555s and had to use 100uf for C3, but only the first press has a delay. You press it the 1st time and it stays on for 3 sec, but any press after that and it’s instantaneous...
View ArticleSmall Transformer 14x19x15h
Damn, cheap Ebay parts caught me out again. Last year I made a circuit on a BB that didn’t work and after a lot of struggling I traced to the short blue wires that came in the Arduino kit, which had...
View ArticleClik here to view.
Small Transformer 14x19x15h
OK with that working, now this should get the trigger working correctly I think: Timing_light_new4_schem.png1611x774 65.2 KB The 560K/ 330K (R3/R4) voltage divider should provide around 4.4 volts with...
View ArticleClik here to view.
Does an Arduino Uno Mega Shield SD Card ICSP SPI Exists Already?
Eddiie: Lastly, if I add my own SD card, is there a chip of some sort needed? Or do the pins go directly to the ICSP pins? My existing shield looks like it has a real small ship with no markings that...
View ArticleSmall Transformer 14x19x15h
I’m confused about the junctions - I know you don’t use FZ much -, but is the link from R4 to C1 jumping over the link from pin 2 to the pickup wire L1, or connected to it, ie a 4 point junction.
View ArticleClik here to view.
How to créate a streapboard the same like in the picture?
Peter and Old_Grey thank for that ! Just in case … would it be possible to use the components that are used for printed circuit in Fritzing ?
View ArticleSmall Transformer 14x19x15h
You are right there should be a dot at the r4 /L1/C1 junction as R4 should connect to the trigger line. I missed that when I modified the drawing. The idea is when the coil is not active (due to no...
View ArticleHow to créate a streapboard the same like in the picture?
Not directly in breadboard. Inside Fritzing there are different svg (a graphic format) files for each view. Typically the ones used for breadboard have been made to look like the component tilted at...
View Article