Multiple PCB on 1 gerber file
This may work… I cannot guarantee exact placement of board and rectangle, ect. You might have to consult with the fab house to make sure they can v-cut as necessary. I’m sure you can make due this way
View ArticleClik here to view.
Multiple PCB on 1 gerber file
Fifteen years ago, PCB houses happily sectioned boards if I sent them a CAD file of it. I don’t know what they do ‘today’ because I’ve made my own boards since (via CNC). However, the approach is the...
View ArticleGPD2846A - TF Card MP3 Decoder Board Module
GPD2846A - TF Card MP3 Decoder Board Module GPD2846A.fzpz (17.8 KB)
View ArticleHum-900-prc part
Either module will work fine in fritzing. BUT if used on a 2-layer board only, I would call it a BETA unit used for designs and in-house reference only. NOT used in a final product to...
View ArticleLooking for an STM32 Blue Pill Part
Thanks, used that. Does not have copper pads for the bottom layer. Tried unziping fzpf and editing the svg.pcb.xxx.svg to the same pattern as a different part. reziped imported without error, reloaded...
View ArticleLooking for an STM32 Blue Pill Part
You just put copper1 inside a group called copper0.
View ArticleHum-900-prc part
The pdf says "The castellation connection for the antenna on the pre-certified version allows the use of embedded antennas as well as removes the cost of a cable assembly for the U.FL connector....
View ArticleLooking for an STM32 Blue Pill Part
I tried that - no joy. I also looked at other svg.pcb.xxx.svg’s In those copper1 contains copper0. That does not work either. This is what I have now. <g...
View ArticleLooking for an STM32 Blue Pill Part
I can make it double sided but I can’t get rid of the layer warning and that annoying empty VBAT pad, plus there is a lot of stuff in silk that is not needed, so I think we need Vanepp.
View ArticleLooking for an STM32 Blue Pill Part
What did you do to make it DS ? I am trying to get better at this ? I only care a little about the warnings - if it will route both sides.
View ArticleLooking for an STM32 Blue Pill Part
Go to XML Editor in INK. Select g:557 Then Object Ungroup, Ungroup. Select copper1, go to id, change to copper0 and set. Still on copper0 go Object Group and name that copper1. Extras are Ungroup...
View ArticleClik here to view.
Does an Arduino Uno Mega Shield SD Card ICSP SPI Exists Already?
Hi Peter, This is not working in my scenario for some reason. Can you see what is wrong? I ordered this part - https://www.mouser.com/ProductDetail/595-SN74AHC125NE4 Here is my schematic -...
View ArticleSmall Transformer 14x19x15h
Preliminary brightness testing only, no accuracy testing. With old LED timing light circuit :- 1 - 4 off 5mm LEDs 2 - 8 off 5mm LEDs - resistor value wasn’t reduced for larger current draw, so light...
View ArticleCreating a wire
Hello friends, would there be someone nice here, to make me a simple electric wire? I did not find that kind of thing to download. I wish I could change its length, color and thickness (fine wire) ....
View ArticleTo substitute parts wiew
Ability to use components allocated in the schematic view for the breadboard or streapboard , if it’s possible .
View ArticleLooking for an STM32 Blue Pill Part
Thank you getting that right was tedious. Aparently loading and saving in parts editor after editing with inkscape is critical
View ArticleCreating a wire
In which view? BB makes it’s own wires, and in SCH and PCB you link a wire from your start point make a temporary connection to any part. Then you add a bendpoint and Delete wire up to bendpoint, and...
View ArticleTo substitute parts wiew
I think it’s possible. You can save it as a new part, pull the SCH view svg from it and load it back into BB view.
View ArticleMark groundfill seed pins as connected
When a connection is marked as a groundfill seed, and there are no wires connected to it, that connection is represented as unconnected.
View ArticleCreate a VCC Seed option
Groundfilling is very useful. But it should be possible to VCC fill the opposite layer of the board, and it should be possible to mark a pin as VCC Seeded.
View Article