Do you recognise a 6 pin oled display?
Where does it store the files it brings up in mine and temp?I was wanting to send you a copy of the the finished item.
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
I think that may be the one that I found (I don't seem to have kept where I got it from). Yes you can get rid of the extra pins but you likely have to edit the svg files with Inkscape to do so. If you...
View ArticleClik here to view.
Thoughts on this circuit (My first one)
thanks for the reply, very informative! Yes this is only an exercise (at least at the moment it is). I would like to actually fabricate this design sometime in the future but of course I want to make...
View ArticleClik here to view.
Parts: db9 pin number
in the db9 male or female partthe pins 2 and 3 are missing and there is an extra pins 10 and 11. ... My version of Fritzing and my operating system: Version 0.9.3... db9.gif929x795 40.5 KB Please also...
View ArticleUltrasonic sensor
I think elaborate in this context is more along the lines of a datasheet for the ultrasonic sensor (which I assume isn't one of the 40khz distance sensors but rather some medical device) and what it...
View ArticleClik here to view.
Thoughts on this circuit (My first one)
As I said, it is likely more economical to buy a module off ebay or sparkfun (the entire module is likely cheaper than you getting a single board), however if you want to do it as a learning...
View ArticleDo you recognise a 6 pin oled display?
my board, with the pin strip along the bottom as it shows on the picture is d/c cs MOSI clk gnd vcc
View ArticleDo you recognise a 6 pin oled display?
Just so I'm clear the pins look like this: Nokia Yours 1 VCC VCC in pcb view the one with the square around the pad in breadboard the extreme left2 GND gnd3 SCE clk4 RST MOSI5 D/C cs6 DN d/c and pins...
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
No, VCC is at the other end. I was going to try to cancel pins 1 and 8 and leave the others in the centre, your list is correct but running from right to left matelot: my board, with the pin strip...
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
vanepp: As well do you have a partnumber for your display to replace the Nokia 5110 currently there? the ones I have are Nokia 5110 LCD Module2 and 3 and 4 but I could delete any two or all three and...
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
Going to be more complex than I thought. The full Nokia I have is all png images not an actual svg (I haven't yet had time to actually get to the Nokia in Fritzing) and so can't be changed (at least...
View ArticleDo you recognise a 6 pin oled display?
thank you I really appreciate your input in this. I wish I could see you do it.
View ArticleParts: db9 pin number
Can you not just rename the pin numbers? It is a 9 pin connector.
View ArticleLinux fails on fatal IO error 2
I want to ask a couple of questions: What version of Fritzing are you trying to use?Was it installed with the DE package manager/
View ArticleThoughts on this circuit (My first one)
Your the best!! Thank you so much.yes im really just teying to learn how hardware works. (Im more of a software guy) so a learning exercise this is. Thanks again.
View ArticleThoughts on this circuit (My first one)
It really is good to know both. I trained originally in hardware and switched to software about 5 years in (in microprocessors) 40 or so years ago and being able to sketch on a napkin the circuit that...
View ArticleGround fill thermal relief
yep, i built a couple board designs with ground planes using that method, setting ground fill seeds, and such, and just letting fritzing make the connections to the plane. both for thru hole and...
View ArticleConnect traces to planes
Very much appreciate the advice in these replies. Very helpful indeed.
View ArticleClik here to view.
Ground fill thermal relief
Isn't this enough. Set part - Set Ground Fill Seed. Make - Routing/Ground Fill/Set Ground Fill Keepout, very big.Then - Routing/Ground Fill/Choose Ground Fill Seeds/OK and ground fill.
View ArticleGround fill thermal relief
those are much larger than i have previously observed. i didnt change the keepout, so they were most likely set at default. will give this a try before getting more elaborate. thanks for the example.
View Article