Clik here to view.
Vibration Sensor module SW-420 custom part
enjoy [specs here] Vibration sensor module.fzpz (10.2 KB)
View ArticleDo you recognise a 6 pin oled display?
Has anyone any information, a fritzing part hopefully, about a nokia 5110 type oled display made by heltec that has six pinsvccgndclkmosicso/cI did get it working long ago but have lost all the...
View ArticleHelp with fritzing circuit
Hi! I'm trying to make a charging circuit for my go kart using a 48volt generator connected to 4 packs of 12 volt parallel batteries. I am using the axle of the go kart to generate power while...
View ArticleClik here to view.
Thoughts on this circuit (My first one)
I put together a simple ATmega circuit to run arduino code. I am wondering whether I set my pcb up in a good way or is it ass backwards and shitty. thank you guys. PCB.PNG1159x750 104 KB <img I...
View ArticleLinux fails on fatal IO error 2
When i try to run Fritzing nothing happens, and when I try to run it from the terminal the loading window briefly appears and then this error is displayed in the terminal: qt.network.ssl: QSslSocket:...
View ArticleConnect traces to planes
I would like to create a custom shaped "copper plane" that i can then use as a "bus", that will have traces terminated to the bus along its length. I've had success using the copper blocker feature to...
View ArticleGround fill thermal relief
After building a few boards, I've observed that manual soldering and rework of components connected to the ground plane is a real pain and takes special attention to avoid poor solder joints or...
View ArticleConnect traces to planes
Yep, that is the way you do it... You can set the "connect to" N, E, W, S, and center... You can also drag the trace through the copper plane and come out any where you want, the trace and copper...
View ArticleThoughts on this circuit (My first one)
Not a bad attempt, but your diode appears to be in backwards (the cathode needs to go towards the voltage regulator to conduct). The leads on your crystal are also too long (I'm assuming a standard...
View ArticleHelp with fritzing circuit
You would need to provide a diagram of how the batteries are to be connected to be charged. If the 4 batteries are in parallel the output will be 12 Volts and your generator is providing up to 48V...
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
There is an 8 pin Nokia 5110 Fritizing part available in the projects section of the main web site (a good place to look for odd parts ) that you could likely modify.
View ArticleUltrasonic sensor
I have a biomedical project and i have to use an ultrasonic sensor. Any ideas or suggestions ?
View ArticleGround fill thermal relief
There are a couple of ways you can make a thermal relief... depending on what you are trying to do and if your board is DIY or fabricated by a PCB fab house. The copper pad when commercially made will...
View ArticleUltrasonic sensor
I think you need to elaborate a little bit... Are you building a project or just want to create a breadboard view...
View ArticleConnect traces to planes
Thanks for the advice. I was referring to a copper fill as a plane. So the workflow would be to drop a 'copper pad' onto the pcb, size it as a long rectangle to mimic my bus. Where i'm a bit fuzzy is...
View ArticleConnect traces to planes
Yep, copper is copper... it is just all one layer, it does not make any difference if it is a pad or fill... if it connects in the view then it will connect when fabricated. WYSIWYG...
View ArticleGround fill thermal relief
Fritzing has thermal relief. Right-click on part, Set Ground Fill Seed.
View ArticleConnect traces to planes
You don't necessarily have to connect to the pad. You can run the trace normally and put a pad on top of it, or put via at each end and connect with a trace set to it's maximum 128mil.
View ArticleClik here to view.
Do you recognise a 6 pin oled display?
Thanks for that.I went to the projects section, downloaded the nokia 5110.fzz from herePut it into parts editor and managed to alter the pins (is there any way to get rid of the two spare ones? I just...
View Article