Clik here to view.
PCB connections completely incorrect
Steps I took that resulted in the problem: Created breadboard projects, router parts on schematic view. PCB view shows connections between parts, that are not electrically connected. It also misses...
View ArticleCustom shapes for the solder mask blocker
No since we are talking about only removing solder mask not creating a hole. I'm looking for an LED to shine through the actual fiberglass which looks really beautiful.
View ArticleCustom shapes for the solder mask blocker
There is a way... What size do you want the circle?
View ArticleClik here to view.
0.9.3b unusable on 1080p display with 1.25x scaling
I can confirm I have a similar problem on windows 8.1. I have a screen resolution of 1920x1080 image.png1920x1080 184 KB Is there a quick workaround for windows?
View ArticleClik here to view.
Help please to edit a component in inkscape and then use it
I am trying to alter a part from the library with my very limited knowledge of how to do it.I managed to load the original relay from the fritzing library into inkscape and altered it to this (the...
View ArticleClik here to view.
Help please to edit a component in inkscape and then use it
Start here Part Creation - A very rough how-to parts help You would need a whole series of videos, but this is a quick one to show some tips. This is not a proper guide, just methods to do stuff....
View ArticleHelp please to edit a component in inkscape and then use it
OK thanks I will take a look at that.
View ArticleClik here to view.
Bridge rectifier
DB107 Bridge rectifier created parts submit DB107.fzpz (10.3 KB) Glass passivated bridge rectifier Datasheet: http://www.hygroup.com.tw/downloads/prod/file/20150325151647_1.pdf Is the closest I see....
View ArticleClik here to view.
Help please to edit a component in inkscape and then use it
Might want to look at this as well: A new part creation HowTo (long! So long it is in 2 posts) I just replaced the complete text of the first two posts in this thread that make up the howto with a...
View ArticlePCB connections completely incorrect
I think this is more operator error than a bug. For starters in schematic R2 is short circuited by the wire running through it which shorts the fet gate to the drain which is neither intended nor...
View ArticleCustom shapes for the solder mask blocker
I will make it tomorrow for you. Both sides solder mask keepout... correct?
View ArticlePCB connections completely incorrect
If you move R2 in the SCH and PCB it isn't shorted. This is a kind of artifacting that I have seen before, ie extra ratsnests in PCB. I usually just delete that ratsnest and don't worry about it - you...
View ArticleRegarding designing/ordering a motion detection sensor
Hi. I am a beginner and would like to create a motion detection sensor based on small arduino with PIR sensor and bluetooth low energy, but I don't have an experience of designing a schematic or PCB....
View ArticleClik here to view.
Custom shapes for the solder mask blocker
I went ahead and made it, only took a couple of minutes... Solder-Mask-Keepout_12mm.fzpz (2.1 KB) I put a silkscreen around it so you can see where it is at, otherwise it would be invisible. You can...
View ArticleClik here to view.
Regarding designing/ordering a motion detection sensor
Why don't you just order a sensor off of eBay... it would be a lot cheaper...
View ArticleRegarding designing/ordering a motion detection sensor
I thought about buying one off the shelve, but it is because I would like to upload some proprietary code into the arduino. And also there are more business requirements, so I might have to play...
View ArticleArduino Nano V3.0 I/O Expansion Adapter Board Shield
Hi, While I was using fritzing platform, I noticed that the Arduino Nano V3.0 I/O Expansion Adapter Board Shield doesn't exist. The fact is that I need this board shield in order to construct a...
View ArticleClik here to view.
Wemos D1 mini PCB protective areas rotated
Steps I took that resulted in the problem: Used Wemos D1 mini witn "male below". Copper protection areas are rotated 90 degrees. I have project on which I spent many hours, I would like to avoid...
View Article