Parts folder not found
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
View ArticleParts folder not found
I had the same problem then you had 15 minutes ago, then I just found out the solution : In your Application folder, create a folder named Fritzing. Drap and drop all Fritzing files in it. That's it!...
View ArticleAdd enter-able property box for parts in Inspector
I Edit/Save as new part, a Schottky.Then I Edit/META the new part and add voltage and power boxes in Properties, but leave them empty so you can add what you like in Inspector.Back in FZ I pull the...
View ArticleWhat inductor to use with QX5252 joule thief IC?
I have a cheap bad torch (flashlight) and I want to improve it's performance by increasing the current. It uses two white 5 mm LEDs and two AAA batteries to drive them. At 2.7 V, the current is just...
View ArticleAdd enter-able property box for parts in Inspector
There seams to be a big fault in FZ properties. In FZ part Edit you can add different properties, but they don't work in Inspector.More weirdness.I was able to delete the value of a part in...
View ArticleClik here to view.
7-Lead TO-220 for OPA548
Hi everybody! As I was running into the need of using a high voltage, high current amplifier for a temperature controller, I thought it would be nice to make the circuit in fritzing :-). As I didn't...
View Article7-Lead TO-220 for OPA548
There are a couple of a technical errors, which aren't important, but the glaring one is that there is no copper0 (bottom copper) to make it suitable for single and double sided PCBs. Just make a...
View Article7-Lead TO-220 for OPA548
Thanks for the feedback. I fixed the errors mentioned by Old_Grey. Here is the second, improved version of the part! OPA548(Rev2).fzpz (15.2 KB)
View ArticleClik here to view.
Making PCB pads connectable?
Yes, I am doing that now, using test points stacked with pads. Effective with only double the work. Imagine how much simpler it would be to create some of these oddball SMD footprints (and other...
View ArticleClik here to view.
Making PCB pads connectable?
I literally make at least one new one-off part per week. If I need a 0.650" resistor I pull the svg, move the nodes, put it back in, and 3 min latter bang it's done. Then I share it to help the...
View ArticleClik here to view.
Silicon Heating pads
HeatPad(All).png1772x1044 33.5 KB A simple heating pad (taken from a rectangular model made with silicon), used to transform electric power into heat. The next file contains the breadboard, schematic...
View ArticleClik here to view.
New parts editor not available
I am seeing this issue, when exporting to SVG my custom parts are missing from generated SVG.What could be wrong?Same issue here: github.com/fritzing/fritzing-app Issue: SVG export skips image for...
View ArticleCapital Advanced "surfboards"
Brand new to Fritzing and it looks like a great tool so far. I was a little surprised that I could not find any of the Capital Advanced "surfboard" parts in the system as they're great building blocks...
View ArticleTransmitter and receiver 433MHz arduino
I want to know how can i send a int values from the transmitter to the receiver from RF 433MHz Transmitter/Receiver ?I'm reading values from a sensor and i want to transmitted to the receiver ?
View ArticleFritzing will not open
When attempting to open Fritzing the splash screen shows then Fritzing shuts down. No messages are displayed. Steps I took that resulted in the problem: Double-clicked "Fritzing.exe"... What I...
View ArticleNew parts editor not available
Either you are tickling the same bug (it doesn't look to be resolved yet) or have the same problem (i.e. the breadboard group is missing in your part(s)). I expect your best bet would be to post the...
View ArticleFritzing will not open
By the flash screen you mean the Red box with Fritzing beta I assume? If so do you get the pop up box below it with Loading and a progress bar under it? The first thing I'd do is check that your...
View ArticleClik here to view.
Add enter-able property box for parts in Inspector
Added 6 things in Part Edit properties, and nothing. r07kl0n9d7pcbop6g.jpg916x594 61.4 KB Even in the .fzp file, which you shouldn't have to directly hack, there is no way to discern between an...
View Article