Working with veroboard/stipboard
Hi guys, I am new to Fritzing, but have been making my own PCB etc since at least the 1970s. I recently decided to make a project that was basically a small 12V gel battery charger and LED state of...
View ArticleClik here to view.
Working with veroboard/stipboard
Yeah, you can't see the other side of stuff except in PCB view. Some people make a stripboard in PCB view, but it is a bit of work. This vid might answer the part creation thing. Part Creation - A...
View ArticleClik here to view.
Part needed to complete fritzing
Can someone help me build part like in the image?Part include:1-12v relay module2-12v adapter3-ttp223 touch sensor4-arduino uno5-cable wire IMG_7039.JPG2448x3264 1.33 MB
View ArticleClik here to view.
Part needed to complete fritzing
IMG_7038.JPG2448x3264 1.23 MB This is the second picture that related to the first picture
View ArticleLinux fails on fatal IO error 2
I got libssl1.0.0 installed on version 1.0.2g-1ubuntu9.And openssl is also installed on version 1.0.2g-1ubuntu9.
View ArticleLinux fails on fatal IO error 2
Tried sudo apt-get build-dep fritzing but it gives E: You must put some 'source' URIs in your sources.list
View ArticleClik here to view.
Clik here to view.
Linux fails on fatal IO error 2
Greenscreener: E: You must put some 'source' URIs in your sources.list please read askubuntu.com Adding Source URIs apt, dependencies asked by Bryce on 07:13PM - 06 Jul 16 See if you can get source...
View ArticleLinux fails on fatal IO error 2
Done. Now what? The Fritzing command segfaults the same way. Also, sudo apt-get build-dep fritzing installed a LOT of packages. Is that supposed to happen?
View ArticleLinux fails on fatal IO error 2
I would think if you had fritzing 0.9.2 from the repos install before, there shouldn't have been many more packages t install, unless you had uninstalled it prior to the above command.
View ArticleHelp with fritzing circuit
Thanks for the information! Would you help me on the whole charging circuit?
View ArticleHelp with fritzing circuit
I'm not sure I know enough about lead acid chargers to do that safely. A quick google search indicates that there does need to be over charge protection but I don't know how to do it. You would be...
View ArticleClik here to view.
Hologram Dash - Cellular MCU
There are actually a few more problems than that. There is a bus on pins 1 and 2 and 3 and 4 which short pin 1 and 2 and 3 and 4 (and since 1 is +5V and 2 is gnd, I'm fairly sure this wasn't intended...
View ArticleFritzing window sizing on ubuntu 16.10 issue
Steps I took that resulted in the problem: pulled the correct arch of the linux fritzing, extracted and ran the Fritzing executable. application loads but looks 2x the scaling on my 1080 resolution......
View Article0.375in Pin Spacing on header?
I'm trying to create 4 pin header with 0.375in pin spacing on my PCB. This is to interface with an bunch of odd sized ribbon cables on the gadget I'm trying to modify. I figured I could use the...
View ArticleClik here to view.
Hologram Dash - Cellular MCU
OK, this was an interesting exercise as your part is broken in interesting ways with the note that I'm not an expert at any of this (I'm just learning Fritzing part creation and know very little about...
View Article0.375in Pin Spacing on header?
Assuming I've understood your request correctly this should do it. 4 .1 pins (.038 hole) on .375 centers. I only changed pcb, breadboard is still .1 spaced but I can change that if you need it....
View ArticleClik here to view.
Help with fritzing circuit
Making a circuit isn't a problem, its knowing what the circuit needs to do that is the problem. A partial list of the things I don't know: 1) can you charge series connected lead acid batteries? You...
View ArticleNeed to import smoothiboard from github
Hi everyone, I'm hoping there is a simple fix to this. I'm new to Fritzing and I am trying to import a part. Some one has already done all the work to make a smoothieboard part and post it on Github,...
View Article