Clik here to view.
Learning Fritzing, beginning difficulties
Yes the file format at least is here https://github.com/fritzing/fritzing-app/wiki/2.1-Part-file-format as far as I know the parameters that Fritzing understands are not documented outside the source...
View ArticleLearning Fritzing, beginning difficulties
Well, according to the Wikipedia article on Inkscape, Inkscape is a fork of Gimp. Argue with them if you like, I don't have a stake in it. I just tried the procedure you mentioned above. Saved as a...
View ArticleLearning Fritzing, beginning difficulties
@vanepp: OK, thanks, I'll take a stab at it. I'm somewhat familiar with image processing from a technical-user perspective, although I don't claim to be a graphics programmer. As I mentioned above, I...
View ArticleLearning Fritzing, beginning difficulties
If you can't make it work, post and I'll make one for you. Its easy enough when you've done it a few times but I suspect you will do fine anyway. Unlike Old_Grey I've never figured out the parts...
View ArticleClik here to view.
Learning Fritzing, beginning difficulties
@vanepp: Understood, and thank you. It'll be educational, I'm sure.
View ArticleClik here to view.
Learning Fritzing, beginning difficulties
I thing this is included in my part... Pasted image1217x853 17.7 KB
View ArticleClik here to view.
Is it possible perhaps a Daft question
Hi vanepp, thank you very much for your reply, the only diagram I have is a jpeg image of a photo (find Attached), I think the 3rd shift register was added for future expansion, it needs 2 because I...
View ArticleClik here to view.
Blank RPi HAT PCB
Tenderfoot14: @steelgoose Could you create one of these templates for the Pi Zero? Sure, I will work on it today...
View ArticleClik here to view.
Raspberry Pi code?
Someone made one back in March. Here is the Fz link; Raspberry Pi 3 Fritzing Part parts submit Its been some time since the release of the mighty Raspberry Pi 3 and its about time we had a part for...
View ArticleIs it possible perhaps a Daft question
[I hope I am not asking to much but would you mind doing a breadboard?] Hi vanepp. Can you hold up doing the breadboard as I have had a good look and tinkered about a bit and I think I might be able...
View ArticleFritzing Massesymbol
Hi,ich habe heute in Fritzing eine kleine Schaltung mit einem Arduino erstellt.Nun ist meine Frage wie ich das Massesymbol verwende welches beim Stockprogramm dabei ist bzw. wie ich dieses an eine...
View ArticleIs it possible perhaps a Daft question
Hi all, what a very impressive piece of software, tomorrow I will find out if works,Terry switch 1.fzz (68.2 KB)
View ArticleCant change the layering in breadboard view!?
Is there a way to change the layering so that the parts layer always goes in front of the wires layer?
View ArticleClik here to view.
Is it possible perhaps a Daft question
Looks like you pretty much have it in hand and yes Fritzing (even with its bugs) is impressive. The 4 values comment relates to what I think the leds are intended for. Each servo seems to have 2 leds...
View ArticleClik here to view.
Looking to pay someone to create a large part
OK, but it may take me some time my first pass at adding the lcd and a 9 pin connector to the breadboard part has run in to an issue where the 9 pin connector pins don't work in breadboard (but do...
View ArticleClik here to view.
Downloading & installing Fritzing on Ubuntu Linux problem
landracer: Then extract that tarball. Go to download folder, then extract, change folder, then run.cd ~/Downloadstar -xzf fritzing-0.9.3b.linux.AMD64.tar.bz2 cd fritzing-0.9.3b.linux.AMD64./Fritzing...
View ArticleDownloading & installing Fritzing on Ubuntu Linux problem
With the caution that you want to be vary sure you are in the correct directory (because this could erase your entire system if done incorrectly, so make sure you have a backup!): cd...
View ArticleClik here to view.
Looking to pay someone to create a large part
Fixed that problem they used breadboardbreadboard (rather than breadboard) for the layer ID fixing that looks to have fixed my breadboard connector problem. A question: I assume switches b0 to b3 are...
View ArticleClik here to view.
Standard headers & header spacing
Hi guys, I tried to make the schematic better, but i don't understand the black dot system. As you can see here when i highlight it everything is connected: However if I don't highlight it then i have...
View ArticleClik here to view.
Standard headers & header spacing
Sorry image had to come in the second post because i'm new -.- (what an annoying rule)
View Article